Airtac 3V1 Solenoid Valve 3V1M5F10F
The AirTAC Airtac 3V1 Solenoid Valve 3V1M5F10F is a genuine 3-port 2-position (3/2) solenoid valve with M5 ports. It either feeds its outlet or vents it to exhaust, which is what makes it the valve for single-acting cylinders, on/off air blow, clamping, vacuum switching and pilot duty.
- Valve type3/2-way (3-port, 2-position)
- Port sizeM5
- Coil voltageDC12V
- Electrical entryDIN plug (DIN socket type)
- Stations10
- Series3V1
About the Airtac 3V1 Solenoid Valve 3V1M5F10F
Ten complete 3V1 3/2 solenoid valves come factory-integrated on this manifold assembly, each with its own M5 port and its own DC12V DIN-plug coil drawing just 2.5 W. Every valve is direct acting with a single solenoid and spring return: it feeds one line or vents it, which suits single-acting cylinders, clamps, air blow and piloting larger valves. One common supply plus one wiring run keeps a ten-valve panel small.
Commissioning is helped by the manual override on each station. Air must be filtered through a 40 um or finer element, with no lubrication needed. Remember that 3V1 is supplied in a single fixed initial state - check the datasheet to confirm it.
Airtac 3V1 Solenoid Valve 3V1M5F10F Technical Specifications
| Model | Airtac 3V1 Solenoid Valve 3V1M5F10F |
|---|---|
| Series | 3V1 |
| Valve type | 3/2-way (3-port, 2-position) |
| Function | Direct-acting, single solenoid, spring return |
| Port size | M5 |
| Thread | PT |
| Coil voltage | DC12V |
|---|---|
| Electrical entry | DIN plug (DIN socket type) |
| Coil power | 2.5 W |
| Operating pressure | 0-0.8 MPa (0-114 psi) |
| Vacuum service | Not rated for vacuum |
| Flow coefficient | Not published for 3V1 |
| Temperature | -20 to 70 C |
| Construction | Direct-acting, single solenoid, spring return |
| Protection | IP65 (DIN 40050) |
| Medium | Air, filtered by a 40 µm or finer element. Lubrication not required. |
Figures follow the official AirTAC 3V1 catalogue. Confirm coil voltage and thread (PT / NPT / G) against the product label before wiring.
Model Code: Airtac 3V1 Solenoid Valve 3V1M5F10F
| 3V1 | Body — sets the flow, the coil power and whether vacuum is rated. |
|---|---|
| M5 | Port size. M5, 06 = 1/8 in, 08 = 1/4 in, 10 = 3/8 in. |
| DC12V | Coil voltage. A = AC220V, B = DC24V, C = AC110V, E = AC24V, F = DC12V. |
| — | Electrical entry: I = flying lead, otherwise a DIN plug. |
| 10F | 10 stations in one assembly. |
| PT | Port thread. PT ships from stock; G and NPT are available to order. |
What a 3/2 Valve Does
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
Where the Airtac 3V1 Solenoid Valve 3V1M5F10F Is Used
PCB transfer fixture
Ten valves on one manifold actuate the individual clamp pins of a printed-circuit-board handling fixture, each M5 outlet feeding its own small spring-return pin cylinder.
Ampoule blow-off row
A row of M5 nozzles blows moisture off glass ampoules on a pharmaceutical filling line; each 3/2 valve opens one jet and vents the line when de-energised.
Test-bench pilot stage
At 2.5 W per coil, the ten-station block pilots larger process valves on a low-voltage rig without straining its limited power supply.
Is the Airtac 3V1 Solenoid Valve 3V1M5F10F the Right Part?
This assembly sits at the bottom of AirTAC's 3V range for size and power, so check two directions before you buy. If M5 flow is marginal, move up to 3V2 (1/8" and 1/4" bodies, NC or NO selectable, Cv 0.18-0.19, also vacuum rated) or to 3V3 at 1/4" with Cv 0.62; pick 3V2M instead when manifold density outranks flow. Flow coefficient is not published for 3V1, so send flow-critical duties to us for confirmation.
Confirm five things when ordering: M5 or 1/8" port (thread codes G and NPT exist only on the 1/8" 06 version), coil voltage, DIN plug versus flying-lead entry, the number of manifold stations you need, and the fixed initial state of the valve. For a double-acting cylinder, specify the 5-port AirTAC 4V series instead.
Confirm before you order
- ✓ Port size and thread (PT from stock; G / NPT to order)
- ✓ Coil voltage matches your controller output
- ✓ Electrical entry — DIN plug or flying lead
- ✓ Single valve, bare base, or complete assembly
- ✓ Single-acting duty, not double-acting
Installation & Wiring Notes
- check Use clean air filtered to 40µm or finer.
- check Stay within 0-0.8 MPa (0-114 psi) operating pressure.
- check Match the coil voltage to your controller output.
- check Use the manual override to test before powering up.
- check Leave the exhaust port clear, or fit a silencer.
- check Blank any unused station on the base before pressurising.
- check Wiring by qualified personnel, per AirTAC documentation.
Airtac 3V1 Solenoid Valve 3V1M5F10F FAQ
Operating pressure 0-0.8 MPa (0-114 psi); media temperature -20 to 70 C; protection IP65 (DIN 40050). Coil power by voltage: AC220V 4.5 VA, AC110V 4.5 VA, AC24V 5.0 VA, DC24V 3.0 W, DC12V 2.5 W - this SKU uses the 2.5 W DC12V coil. Air must be filtered to 40 um or finer. No Cv or effective area is published for 3V1.
The 3V1 series accepts 1 to 20 stations in series; this code is the 10-station version, and other counts are available to order. Accessories such as the 3V1-P30 base set, 3V1-P31 O-ring and screw set and 3V1-P32 brackets support the assembly. Only the 1/8" 06 port version carries thread variants - the M5 port here is fixed.
Authorized Export Seller
Genuine AirTAC parts produced by the AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac 3V1 Solenoid Valve 3V1M5F10F
Send us the quantity, coil voltage and destination. We confirm price, stock and lead time — usually within 7-8 hours.