Airtac 3V100 Solenoid Valve 3V110M5NCFI
The AirTAC Airtac 3V100 Solenoid Valve 3V110M5NCFI is a genuine 3-port 2-position (3/2) solenoid valve with M5 ports. A 3/2 valve either feeds its outlet or vents it to exhaust, so it suits single-acting cylinders, air blow, clamping, vacuum switching and pilot duty. We stock this code and confirm its published figures from the datasheet on request.
- Valve type3/2-way (3-port, 2-position)
- Initial stateNormally closed
- Port sizeM5
- Coil voltageDC12V
- Electrical entryFlying lead (lead-out wire type)
- Series3V110
About the Airtac 3V100 Solenoid Valve 3V110M5NCFI
AirTAC's 3V110M5NCFI combines the family's smallest M5 port with a DC12V coil on flying-lead entry. As a normally closed 3/2 valve it keeps the outlet vented until energised, then passes supply air through - a clean fit for small spring-return actuators and short blow-off runs on battery-fed machinery.
This is a genuine AirTAC part. The flying leads arrive pre-wired, which suits cramped enclosures and one-off installations where a plug socket adds bulk. The 3V1 range also offers normally open states, AC220V, AC110V, AC24V and DC24V coils, DIN-plug versions and 3V100M manifold bases carrying several valves on one supply. Figures such as pressure range, flow and coil power come from the datasheet - request them and we will send them across.
Airtac 3V100 Solenoid Valve 3V110M5NCFI Technical Specifications
| Model | Airtac 3V100 Solenoid Valve 3V110M5NCFI |
|---|---|
| Series | 3V110 |
| Valve type | 3/2-way (3-port, 2-position) |
| Initial state | Normally closed |
| Port size | M5 |
| Thread | PT |
| Coil voltage | DC12V |
|---|---|
| Electrical entry | Flying lead (lead-out wire type) |
| Coil power | Confirm from the datasheet — ask us |
| Operating pressure | Confirm from the datasheet — ask us |
| Flow coefficient | Confirm from the datasheet — ask us |
| Temperature | Confirm from the datasheet — ask us |
| Protection | Confirm from the datasheet — ask us |
Model Code: Airtac 3V100 Solenoid Valve 3V110M5NCFI
| 3V110 | Body. |
|---|---|
| M5 | Port size. M5, 06 = 1/8 in, 08 = 1/4 in, 10 = 3/8 in. |
| NC | Normally closed: no air at the outlet until the coil is energised. |
| DC12V | Coil voltage. A = AC220V, B = DC24V, C = AC110V, E = AC24V, F = DC12V. |
| I | Electrical entry: I = flying lead, otherwise a DIN plug. |
| PT | Port thread. PT ships from stock; G and NPT are available to order. |
What a 3/2 Valve Does
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
Where the Airtac 3V100 Solenoid Valve 3V110M5NCFI Is Used
Tray diversion at a packer
A short-stroke spring-return pin pushes off-spec trays off a conveyor lane; the NC valve extends it only while the sensor output holds the coil on.
Service-vehicle air gate
On a van's 12V system, the valve switches air to a small single-acting gate or tool clamp and vents it when the switch is released.
Battery cabinet venting
A 12V DC control board opens a small vent actuator in an off-grid battery enclosure, and the spring closes the vent when power drops.
Is the Airtac 3V100 Solenoid Valve 3V110M5NCFI the Right Part?
Pick normally closed when the actuator should vent on power loss, normally open when it must stay fed. M5 suits the lightest duties; step to 1/8in, 1/4in or 3/8in as the cylinder grows. The 12V DC coil must match the supply exactly, and flying-lead entry means you terminate the wires yourself rather than clipping on a DIN connector.
No flow or pressure data for the 3V1 family appears on this page, so check sizing with us before ordering and we will confirm it from the datasheet. Buyers wanting published figures without waiting can look at the AirTAC 3V2 and 3V3 bodies; a double-acting cylinder is a job for the 5-port 4V series.
Confirm before you order
- ✓ Port size and thread (PT from stock; G / NPT to order)
- ✓ Initial state — NC or NO, ordered up front
- ✓ Coil voltage matches your controller output
- ✓ Electrical entry — DIN plug or flying lead
- ✓ Single valve, bare base, or complete assembly
- ✓ Single-acting duty, not double-acting
Installation & Wiring Notes
- check Use clean air filtered to 40µm or finer.
- check Match the coil voltage to your controller output.
- check Use the manual override to test before powering up.
- check Leave the exhaust port clear, or fit a silencer.
- check Wiring by qualified personnel, per AirTAC documentation.
Airtac 3V100 Solenoid Valve 3V110M5NCFI FAQ
Anything in the datasheet - pressure range, flow, coil power - we will verify and send once the SKU is in an RFQ. This page sticks to configuration. If you need figures published on the page itself, the AirTAC 3V2 and 3V3 series are the documented bodies.
Flying leads suit tight enclosures and direct gland wiring where a connector body would not fit. The valve cannot drive a double-acting cylinder in any case - a 3/2 valve feeds or vents one outlet, and two-way push-pull motion needs the 5-port AirTAC 4V series.
Authorized Export Seller
Genuine AirTAC parts produced by the AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC 3V Valves
Request a Quote for Airtac 3V100 Solenoid Valve 3V110M5NCFI
Send us the quantity, coil voltage and destination. We confirm price, stock and lead time — usually within 7-8 hours.