
The AirTAC 3V220-08 Solenoid Valve, 3V200 Series (3V22008B-AM) is a genuine 3-port 2-position (3/2) solenoid valve with 1/4 in ports. A 3/2 valve either feeds its outlet or vents it to exhaust, so it suits single-acting cylinders, air blow, clamping, vacuum switching and pilot duty. Its published figures are confirmed from the AirTAC datasheet on request.
The 3V22008B-AM belongs to AirTAC's 3V2 family of 3/2 solenoid valves. A 3/2 valve carries a supply, an outlet and an exhaust, and simply switches between feeding the outlet and venting it - the core on/off building block for single-acting pneumatics. Its coil is DC24V, the supply most PLC output cards and modern control panels deliver, and it is wired through a DIN plug. A solenoid is wound for one voltage only: matching coil to panel supply is an ordering decision you make once, not a rewiring job later.
You are buying a genuine AirTAC part. Elsewhere in the 3V1, 3V2 and 3V3 families the same choice pattern applies: NC or NO initial state, five coil voltages, DIN plug or flying lead, and 3V-F manifold bases that share one air supply across several stations. Any figure this page does not carry - pressure limits, flow, coil power, response - comes straight from the datasheet, and we will read it out for you on request.
| Model | AirTAC 3V220-08 Solenoid Valve, 3V200 Series (3V22008B-AM) |
|---|---|
| Series | 3V220 |
| Valve type | 3/2-way (3-port, 2-position) |
| Port size | 1/4 in |
| Thread | PT |
| Coil voltage | DC24V |
|---|---|
| Electrical entry | DIN plug (DIN socket type) |
| Coil power | Confirm from the datasheet — ask us |
| Operating pressure | Confirm from the datasheet — ask us |
| Flow coefficient | Confirm from the datasheet — ask us |
| Temperature | Confirm from the datasheet — ask us |
| Protection | Confirm from the datasheet — ask us |
| 3V220 | Body. |
|---|---|
| 1/4 in | Port size. M5, 06 = 1/8 in, 08 = 1/4 in, 10 = 3/8 in. |
| DC24V | Coil voltage. A = AC220V, B = DC24V, C = AC110V, E = AC24V, F = DC12V. |
| — | Electrical entry: I = flying lead, otherwise a DIN plug. |
| PT | Port thread. PT is standard; G and NPT are available to order. |
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
Switch a spring-return cylinder that presses flaps or seals cartons; loss of signal lets the spring retract the ram.
Drive the coil straight from a 24V DC output card to pressurise or vent the actuator of a larger valve in the panel.
A pedal or pushbutton commands the valve, and the single-acting ram returns by spring between strokes.
Three things fix this configuration: the 1/4 inch port, the DC24V DIN-plug coil and the PT thread (standard on the family; G and NPT are options you can order). The port step matters more than it looks - 1/4 inch serves bigger single-acting cylinders and fuller blow duties than M5 or 1/8 inch, while staying a 3/2 valve that cannot drive a double-acting cylinder; for that duty move to the AirTAC 4V 5-port series. The state is not decodable from this code, so say whether you want the outlet dead or live when the coil is off. On sizing: flow figures for this family are not ours to quote, so send us your actuator details and we will confirm fit from the datasheet - or point you at the documented 3V2 and 3V3 bodies, where flow and coil power are published.
Confirm before you order
Those live on the AirTAC datasheet, which we hold on file and will confirm for you on request - send the RFQ and you receive the numbers themselves. If you would rather buy a 3-port valve whose flow and coil power are already published, choose the documented AirTAC 3V2 or 3V3 body instead.
Decide by what must happen at power loss. Normally closed vents the outlet the moment the coil drops out, so the actuator releases. Normally open keeps the outlet fed, so the actuator holds until you switch it. Pick the behaviour that keeps your machine safe and order that state code. Note the limit too: one outlet means single-acting loads only - a double-acting cylinder needs a 5-port 4V valve.
Genuine AirTAC parts produced by the AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity, coil voltage and destination. We confirm price, availability and lead time — usually within 7 hours.