AirTAC 3V320-10 Solenoid Valve, 3V300 Series (3V32010BI)
The AirTAC AirTAC 3V320-10 Solenoid Valve, 3V300 Series (3V32010BI) is a genuine 3-port 2-position (3/2) solenoid valve with 3/8 in ports. A 3/2 valve either feeds its outlet or vents it to exhaust, so it suits single-acting cylinders, air blow, clamping, vacuum switching and pilot duty. We stock this code and confirm its published figures from the datasheet on request.
- Valve type3/2-way (3-port, 2-position)
- Port size3/8 in
- Coil voltageDC24V
- Electrical entryFlying lead (lead-out wire type)
- Series3V320
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the AirTAC 3V320-10 Solenoid Valve, 3V300 Series (3V32010BI)
The I at the end of 3V32010BI is the electrical entry: flying lead, meaning the coil arrives with pre-wired leads that land directly on your terminals or loom, rather than taking a plug-on DIN connector. Behind that, the code decodes to a 3/2 solenoid valve - supply, outlet, exhaust; feed or vent - on the 3V320 body with a 3/8in port, DC24V coil and PT thread. That is the configuration for a 24V-controlled machine driving a spring-return actuator through a wired-in valve.
It is a genuine AirTAC part. Around it, the family offers normally closed and normally open states, AC220V / DC24V / AC110V / AC24V / DC12V coils, DIN-plug versions of this same valve, and 3V-F manifold bases up to 20 stations. Datasheet figures for the 3V320 - pressure, flow, coil power - are not published on this page; request them via the RFQ and we will confirm them for you.
AirTAC 3V320-10 Solenoid Valve, 3V300 Series (3V32010BI) Technical Specifications
| Model | AirTAC 3V320-10 Solenoid Valve, 3V300 Series (3V32010BI) |
|---|---|
| Series | 3V320 |
| Valve type | 3/2-way (3-port, 2-position) |
| Port size | 3/8 in |
| Thread | PT |
| Coil voltage | DC24V |
|---|---|
| Electrical entry | Flying lead (lead-out wire type) |
| Coil power | Confirm from the datasheet — ask us |
| Operating pressure | Confirm from the datasheet — ask us |
| Flow coefficient | Confirm from the datasheet — ask us |
| Temperature | Confirm from the datasheet — ask us |
| Protection | Confirm from the datasheet — ask us |
Model Code: AirTAC 3V320-10 Solenoid Valve, 3V300 Series (3V32010BI)
| 3V320 | Body. |
|---|---|
| 3/8 in | Port size. M5, 06 = 1/8 in, 08 = 1/4 in, 10 = 3/8 in. |
| DC24V | Coil voltage. A = AC220V, B = DC24V, C = AC110V, E = AC24V, F = DC12V. |
| I | Electrical entry: I = flying lead, otherwise a DIN plug. |
| PT | Port thread. PT ships from stock; G and NPT are available to order. |
What a 3/2 Valve Does
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
Where the AirTAC 3V320-10 Solenoid Valve, 3V300 Series (3V32010BI) Is Used
Wired-in retrofit on an older press
Bringing pneumatic actuation under electrical control on a machine whose panel has no valve connectors - flying leads land straight on the existing terminals.
Lock pin on a machine guard
A spring-return lock pin that holds an access guard shut while the machine is enabled, with the valve switching and venting the pin circuit under the guard controller's command.
Air switching on a filling line
Directing a short blast of air to clear a filling nozzle or nudge a misaligned container between cycles on a bottling line.
Is the AirTAC 3V320-10 Solenoid Valve, 3V300 Series (3V32010BI) the Right Part?
Flying lead or DIN plug is a wiring decision, not a performance one: flying leads suit retrofits and sealed panels where a socket adds a failure point, while a DIN plug lets a maintenance tech swap the coil head without touching the cable. The rest of the configuration is fixed in the code: a DC24V coil (match it to the panel - it cannot be rewired to another voltage) and a 3/8in port, the family's largest, aimed at the larger single-acting actuators. Below that, the 3V2 bodies at 1/8in and 1/4in step down for smaller cylinders.
Before you order, two checks are worth a message to us: sizing the 3/8in port against your actuator's air demand - flow figures for this family are not published here, and we will confirm them from the datasheet - and whether a manifold layout suits the machine, in which case the 3V300M block carries several valves on one shared supply. If the actuator is double-acting, step across to the AirTAC 4V 5-port valves instead.
Confirm before you order
- ✓ Port size and thread (PT from stock; G / NPT to order)
- ✓ Initial state — NC or NO, ordered up front
- ✓ Coil voltage matches your controller output
- ✓ Electrical entry — DIN plug or flying lead
- ✓ Single valve, bare base, or complete assembly
- ✓ Single-acting duty, not double-acting
Installation & Wiring Notes
- check Use clean air filtered to 40µm or finer.
- check Match the coil voltage to your controller output.
- check Use the manual override to test before powering up.
- check Leave the exhaust port clear, or fit a silencer.
- check Wiring by qualified personnel, per AirTAC documentation.
AirTAC 3V320-10 Solenoid Valve, 3V300 Series (3V32010BI) FAQ
Send the requirement through the RFQ - pressure range, flow and coil power are exactly what our engineers confirm from the AirTAC datasheet when we quote. Nothing on this page quotes those figures because we do not publish them for the 3V320 body. Where you need catalogue-published numbers immediately, the AirTAC 3V2 and 3V3 bodies carry them.
Yes - across the 3V3x0 family the same body is offered with coils in AC220V, DC24V, AC110V, AC24V and DC12V, and with DIN plug entry as well as flying leads (the I suffix). NC and NO states are separate order codes too. The coil voltage is fixed at order; it is not something you can convert by rewiring, so pick the one your panel supplies.
Authorized Export Seller
Genuine AirTAC parts produced by the AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC 3V Valves
Request a Quote for AirTAC 3V320-10 Solenoid Valve, 3V300 Series (3V32010BI)
Send us the quantity, coil voltage and destination. We confirm price, stock and lead time — usually within 7-8 hours.