This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACE100X10FB, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACP Compact Cylinder ACP100X10FB
The AirTAC ACP Compact Cylinder ACP100X10FB is a double acting DIN-standard tight/compact air cylinder with a Ø100mm bore and 10mm stroke, 1/4" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACE100X10FB (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ100 mm
- Stroke10 mm
- Port size1/4"
- Acting typeDouble acting
- Rod threadM16×1.5
- StatusDiscontinued → ACE100X10FB
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACP Compact Cylinder ACP100X10FB
A double acting compact cylinder in the AirTAC ACP DIN-standard series, the ACP100X10FB pairs a 100 mm bore with a short 10 mm stroke and an FB flange mount. At 0.5 MPa it pushes 3927 N and pulls 3681.6 N; at 0.7 MPa those rise to 5497.8 N and 5154.2 N, with a theoretical ceiling of 800.9 kgf at 1.0 MPa. The hard-anodized aluminium body and S45C hard-chrome rod keep the package rigid, and the short ISO 21287-class body saves roughly 50% of the mounting length of an ISO 15552 profile cylinder.
Air is supplied through a 1/4" port, the rod end carries a female M16x1.5 thread, and a fixed TPU bumper sits at both ends. Note that this model is discontinued: the current-production direct is ACE100X10, so confirm ISO 21287 mounting dimensions before swapping.
Airtac ACP Compact Cylinder ACP100X10FB Technical Specifications
| Model | Airtac ACP Compact Cylinder ACP100X10FB |
|---|---|
| Series | ACP DIN compact cylinder (discontinued) |
| Replacement | ACE100X10FB |
| Bore size | Ø100 mm |
| Stroke | 10 mm |
| Acting type | Double acting |
| Port size | 1/4" |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACE100X10FB (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | 5154 N |
| Max (@1.0 MPa) | 801 kgf | |
The ACE100X10FB produces the same force from the same bore. Actual usable force is lower than theoretical; size with a margin.
Model Code: Airtac ACP Compact Cylinder ACP100X10FB
| ACP | DIN compact cylinder (double-acting, discontinued). |
|---|---|
| 100 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACP Compact Cylinder ACP100X10FB Is Used
Heavy press-fit clamping
The 3927 N push at 0.5 MPa seats bearings or bushings into aluminium housings on a short 10 mm stroke, ideal where a full-length cylinder will not fit under a press frame.
Injection mold latch locks
A 10 mm stroke is enough to engage and retract mold latch pins on large tooling, with the 1/4" port feeding the high-flow demand of a 100 mm bore.
Replacing the Airtac ACP Compact Cylinder ACP100X10FB with the ACE100X10FB
For a 100 mm bore job this sits at the top of the range: a 63 mm bore delivers about 1558.6 N push at 0.5 MPa, while this 100 mm unit gives 3927 N, so downsize only if the load is well under 2300 N. The 10 mm stroke suits short clamp-and-release or positioning moves rather than long transfers. Remember the rod drifts when air is lost, so add a rod lock or pilot check valve for a held load. FB flange mounting bolts to the standard face, and if you need position sensing, order the -S code to enable CMSE / DMSE switches - without -S there is no magnet. Buy ACE100X10 instead, the current ISO 21287 successor.
Replacement checklist
- ✓ Current-production ACE → ACE100X10FB
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACP Compact Cylinder ACP100X10FB FAQ
Push is 3927 N and pull is 3681.6 N at 0.5 MPa; at 0.7 MPa push reaches 5497.8 N and pull 5154.2 N, with a theoretical maximum of 800.9 kgf at 1.0 MPa. It is a double acting 100 mm bore, 10 mm stroke compact cylinder with a 25 mm rod, female M16x1.5 rod thread, 1/4" port, operating pressure 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, temperature -20 to +70 C, and air filtered to 40 um.
Order ACE100X10. Swap the P for an E and you get the current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and mounting family. Because the ACP was DIN-standard, confirm the ISO 21287 mounting dimensions against your fixture before swapping. The FB flange and I/Y rod knuckles bolt straight to the ISO 21287 face, and the optional -S magnet code enables CMSE / DMSE switches on the ACE.
Related AirTAC ACE Cylinders
Request a Quote for the ACE100X10FB
Send us the quantity and destination. We confirm price, stock and lead time on the ACE100X10FB replacement — usually within 7-8 hours.