This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACE100X10S, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACP Compact Cylinder ACP100X10S
The AirTAC ACP Compact Cylinder ACP100X10S is a double acting DIN-standard tight/compact air cylinder with a Ø100mm bore and 10mm stroke, 1/4" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACE100X10S (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ100 mm
- Stroke10 mm
- Port size1/4"
- Acting typeDouble acting
- Rod threadM16×1.5
- StatusDiscontinued → ACE100X10S
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACP Compact Cylinder ACP100X10S
The ACP100X10S is a double acting DIN-standard compact cylinder with a 100 mm bore and a short 10 mm stroke, fitted with the optional -S magnet so CMSE or DMSE reed and solid-state switches can be mounted directly on the body. At 0.5 MPa it pushes with 3927 N and pulls with 3681.6 N, rising to 5497.8 N push at 0.7 MPa, with a theoretical peak of 800.9 kgf at 1.0 MPa. The hard-anodized aluminium body and S45C hard-chrome rod run on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), 30-500 mm/s.
The short ISO 21287-class body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why this bore size fits clamping stations, press fixtures and gantry Z-axes where a full-length body will not. Note this model is discontinued: the current-production direct is ACE100X10, so confirm the ISO 21287 mounting dimensions before swapping.
Airtac ACP Compact Cylinder ACP100X10S Technical Specifications
| Model | Airtac ACP Compact Cylinder ACP100X10S |
|---|---|
| Series | ACP DIN compact cylinder (discontinued) |
| Replacement | ACE100X10S |
| Bore size | Ø100 mm |
| Stroke | 10 mm |
| Acting type | Double acting |
| Port size | 1/4" |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACE100X10S (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | 5154 N |
| Max (@1.0 MPa) | 801 kgf | |
The ACE100X10S produces the same force from the same bore. Actual usable force is lower than theoretical; size with a margin.
Model Code: Airtac ACP Compact Cylinder ACP100X10S
| ACP | DIN compact cylinder (double-acting, discontinued). |
|---|---|
| 100 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACP Compact Cylinder ACP100X10S Is Used
Press-fit clamping of bearing housings
A 10 mm stroke is ideal for swaging or press-locating bearing housings in automotive fixtures; 3927 N at 0.5 MPa seats parts without a full hydraulic press.
Weld fixture hold-downs
Short-stroke hold-down clamps on car-body weld jigs use the 100 mm bore to hold steel panels against locating pins through the full weld cycle.
Gate or chute diverters in bottling plants
Kicking heavy product gates between lanes needs high force over a tiny travel; the 2356 N usable push and 10 mm stroke suit diverter plates on filling lines.
Replacing the Airtac ACP Compact Cylinder ACP100X10S with the ACE100X10S
For a 10 mm stroke doing heavy clamping or short-lift work, the 100 mm bore gives 3927 N push at 0.5 MPa; if your load is under about 2400 N, the 80 mm bore (2513 N push at 0.5 MPa) saves space and air. If you need more, there is no larger ACP bore, so move to a larger ACE. The 10 mm stroke is well within the 300 mm max standard stroke for this bore. FA/FB flange, LB foot and CA/CB clevis mounts bolt to the same face family as the ACE. A plain cylinder does not hold load when air is lost - add a rod lock or pilot check valve for held positions. Order ACE100X10 as the current replacement and verify ISO 21287 mounting dimensions.
Replacement checklist
- ✓ Current-production ACE → ACE100X10S
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACP Compact Cylinder ACP100X10S FAQ
At 0.5 MPa it pushes 3927 N and pulls 3681.6 N; at 0.7 MPa it pushes 5497.8 N and pulls 5154.2 N. Theoretical maximum is 800.9 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof 1.5 MPa (215 psi), speed 30-500 mm/s, temperature -20 to +70 C. The 25 mm rod ends in a female M16x1.5 thread and the air port is 1/4" (PT).
No - the ACP family is discontinued. The current-production replacement is ACE100X10, the same bore, stroke and force class in the ISO 21287 short body; confirm the mounting dimensions before swapping. This -S version carries the optional magnet, so CMSE or DMSE reed or solid-state switches can be fitted for end-position sensing; without the -S code there is no magnet. Both ends have a fixed TPU bumper, and mounting options include FA/FB flange, LB foot and CA/CB clevis.
Related AirTAC ACE Cylinders
Request a Quote for the ACE100X10S
Send us the quantity and destination. We confirm price, stock and lead time on the ACE100X10S replacement — usually within 7-8 hours.