This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACE100X110, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.

The AirTAC ACP Compact Cylinder ACP100X110 is a double acting DIN-standard tight/compact air cylinder with a Ø100mm bore and 110mm stroke, 1/4" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACE100X110 (ISO 21287 ACE), in the same bore, stroke and force class.
A 100 mm bore short-body cylinder built to the DIN compact format, the ACP100X110 is double acting: air extends and retracts the 25 mm hard-chrome rod. At 0.5 MPa it pushes 3927 N and pulls 3681.6 N, rising to 5497.8 N push at 0.7 MPa, with a theoretical ceiling of 800.9 kgf at 1.0 MPa. The hard-anodized aluminium body and threaded aluminium covers keep the overall length roughly half that of an ISO 15552 profile cylinder of the same bore, so it slots into heavy presses, clamping gantries and machine frames where a full-length body simply will not fit.
The rod end is female M16x1.5 and the air supply connects through 1/4" PT ports. Note that this model is discontinued: the current-production direct is the ISO 21287 ACE100X110, which matches the same bore, stroke and force class - confirm the ISO 21287 mounting dimensions before swapping. Also remember that when air is lost the piston drifts freely; use a rod lock or pilot check valve if the load must stay put.
| Model | Airtac ACP Compact Cylinder ACP100X110 |
|---|---|
| Series | ACP DIN compact cylinder (discontinued) |
| Replacement | ACE100X110 |
| Bore size | Ø100 mm |
| Stroke | 110 mm |
| Acting type | Double acting |
| Port size | 1/4" |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACE100X110 (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | 5154 N |
| Max (@1.0 MPa) | 801 kgf | |
The ACE100X110 produces the same force from the same bore. Actual usable force is lower than theoretical; size with a margin.
| ACP | DIN compact cylinder (double-acting, discontinued). |
|---|---|
| 100 | Bore size in mm. |
| ×110 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
The 3927 N push at 0.5 MPa drives a small scrap-baling or compacting platen on a 110 mm stroke, with the short body fitting inside a guarded press frame.
Double-acting air power swings a sand-gate or chute diverter in a foundry line, with 1/4" PT ports feeding the 30-500 mm/s speed band.
At this bore size the step either side is significant: a 80 mm bore delivers 2513 N push at 0.5 MPa while stepping up is not possible within the family, so 100 mm is the top of the range. If your duty cycle needs position holding under a vertical load, pair the cylinder with a rod lock or pilot check valve rather than relying on the fixed TPU bumpers, which only decelerate at the ends. FA/FB flange, LB foot and CA/CB clevis mountings bolt to the standard face, and CMSE or DMSE switches can be used only if you order the optional -S magnet code - this unit has no magnet fitted. Since ACP is out of production, specify the ACE100X110 as the current equivalent and verify the ISO 21287 hole pattern.
Replacement checklist
At 0.5 MPa it pushes 3927 N and pulls 3681.6 N; at 0.7 MPa those figures rise to 5497.8 N push and 5154.2 N pull. The theoretical maximum is 800.9 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi) with 1.5 MPa (215 psi) proof pressure, speed 30-500 mm/s, and the fixed TPU bumpers decelerate the piston at both ends.
The ACP family is discontinued. The current-production direct is the ACE100X110 (swap the P for an E), an ISO 21287 compact cylinder in the same bore, stroke and force class - confirm the ISO 21287 mounting dimensions before converting. For position feedback, order the -S magnet code so CMSE or DMSE switches can be fitted; without -S there is no magnet in the piston.
Send us the quantity and destination. We confirm price, stock and lead time on the ACE100X110 replacement — usually within 7-8 hours.