This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACE100X110SB, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACP Compact Cylinder ACP100X110SB
The AirTAC ACP Compact Cylinder ACP100X110SB is a double acting DIN-standard tight/compact air cylinder with a Ø100mm bore and 110mm stroke, 1/4" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACE100X110SB (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ100 mm
- Stroke110 mm
- Port size1/4"
- Acting typeDouble acting
- Rod threadM16×1.5
- StatusDiscontinued → ACE100X110SB
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACP Compact Cylinder ACP100X110SB
A double acting compact cylinder built to the DIN-standard short-body format, the ACP100X110SB pairs a 100 mm bore with a 110 mm stroke and a 25 mm hard-chrome S45C rod on a male thread (B code). At 0.5 MPa it pushes 3927 N and pulls 3681.6 N, rising to 5497.8 N at 0.7 MPa, with a theoretical ceiling of 800.9 kgf at 1.0 MPa. The short ISO 21287-class body saves roughly 50% of the mounting length of an ISO 15552 profile cylinder, which is why it slots into heavy gantries and press fixtures where a full-length body will not fit. The -S code on this model means the magnet is fitted, so CMSE or DMSE reed and solid-state switches can be clamped straight onto the tube.
Note that when air is lost the piston drifts - the fixed TPU bumpers at each end only soften end-of-stroke travel and never hold a load, so add a rod lock or pilot check valve for held positions. This model is discontinued; the current-production direct is ACE100X110, so confirm the ISO 21287 mounting dimensions before swapping.
Airtac ACP Compact Cylinder ACP100X110SB Technical Specifications
| Model | Airtac ACP Compact Cylinder ACP100X110SB |
|---|---|
| Series | ACP DIN compact cylinder (discontinued) |
| Replacement | ACE100X110SB |
| Bore size | Ø100 mm |
| Stroke | 110 mm |
| Acting type | Double acting |
| Port size | 1/4" |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACE100X110SB (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | 5154 N |
| Max (@1.0 MPa) | 801 kgf | |
The ACE100X110SB produces the same force from the same bore. Actual usable force is lower than theoretical; size with a margin.
Model Code: Airtac ACP Compact Cylinder ACP100X110SB
| ACP | DIN compact cylinder (double-acting, discontinued). |
|---|---|
| 100 | Bore size in mm. |
| ×110 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACP Compact Cylinder ACP100X110SB Is Used
Clamping heavy weld fixtures
With 3927 N of push at 0.5 MPa and a 110 mm stroke, the cylinder clamps large steel weldments in automotive fixture trees where the short body must fit between fixture rails.
Press-fit ejection stations
The 100 mm bore ejects bushings and bearings from press dies; plan on about 240 kg of usable force at 0.5 MPa and confirm the 1/4" port matches the valve manifold.
Pallet gate and stopper actuation
In warehouse conveyor lines the 110 mm stroke raises and lowers heavy gate stops, and the fitted -S magnet allows CMSE or DMSE switches to signal gate-up and gate-down to the PLC.
Replacing the Airtac ACP Compact Cylinder ACP100X110SB with the ACE100X110SB
At this force class the 100 mm bore sits at the top of the range: a 80 mm bore gives 2513.3 N push at 0.5 MPa and there is no larger bore in the family, so if 3927 N is marginal you need a different series rather than a bigger ACP. If the job needs far less force, the 63 mm bore delivers 1558.6 N push at the same pressure. Ports are 1/4" on this bore, the standard stroke tops out at 300 mm so 110 mm is comfortably in range, and mounting options include FA/FB flange, LB foot and CA/CB clevis. Because the ACP is discontinued, order ACE100X110 as the current equivalent and verify the ISO 21287 hole pattern against your fixture.
Replacement checklist
- ✓ Current-production ACE → ACE100X110SB
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACP Compact Cylinder ACP100X110SB FAQ
At 0.5 MPa the cylinder delivers 3927 N push and 3681.6 N pull; at 0.7 MPa that rises to 5497.8 N push and 5154.2 N pull. The theoretical maximum is 800.9 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof pressure, speed 30-500 mm/s, and the piston drifts if air is lost - add a rod lock or pilot check valve to hold position.
Yes, the ACP100X110SB is out of production. The current direct is ACE100X110 - swap the P for an E - which matches the same 100 mm bore, 110 mm stroke and force class in the ISO 21287 family. Before swapping, confirm the ISO 21287 mounting dimensions against your fixture because the ACP was built to the DIN standard. The -S magnet on this model is carried as an option on the ACE, so CMSE and DMSE reed or solid-state switches still work; the male rod thread (B) and 1/4" PT port also carry over.
Related AirTAC ACE Cylinders
Request a Quote for the ACE100X110SB
Send us the quantity and destination. We confirm price, stock and lead time on the ACE100X110SB replacement — usually within 7-8 hours.