This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACE100X175SB, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACP Compact Cylinder ACP100X175SB
The AirTAC ACP Compact Cylinder ACP100X175SB is a double acting DIN-standard tight/compact air cylinder with a Ø100mm bore and 175mm stroke, 1/4" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACE100X175SB (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ100 mm
- Stroke175 mm
- Port size1/4"
- Acting typeDouble acting
- Rod threadM16×1.5
- StatusDiscontinued → ACE100X175SB
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACP Compact Cylinder ACP100X175SB
The ACP100X175SB is a double acting DIN-standard compact cylinder with a 100 mm bore and 175 mm stroke, delivering 3927 N push and 3681.6 N pull at 0.5 MPa. Its short ISO 21287-class body saves roughly 50% of the mounting length of an ISO 15552 profile cylinder, which is why it fits dense press fixtures and gantry frames that cannot swallow a full-length body. The hard-anodized aluminium barrel carries aluminium covers, an S45C hard-chrome rod with male thread, and fixed TPU bumpers at both ends.
This unit carries the optional -S magnet, so CMSE or DMSE reed and solid-state switches can be clipped on for end-of-stroke signalling. Note that ACP is discontinued: the current-production direct is ACE100X175, and ISO 21287 mounting dimensions should be confirmed before swapping.
Airtac ACP Compact Cylinder ACP100X175SB Technical Specifications
| Model | Airtac ACP Compact Cylinder ACP100X175SB |
|---|---|
| Series | ACP DIN compact cylinder (discontinued) |
| Replacement | ACE100X175SB |
| Bore size | Ø100 mm |
| Stroke | 175 mm |
| Acting type | Double acting |
| Port size | 1/4" |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACE100X175SB (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | 5154 N |
| Max (@1.0 MPa) | 801 kgf | |
The ACE100X175SB produces the same force from the same bore. Actual usable force is lower than theoretical; size with a margin.
Model Code: Airtac ACP Compact Cylinder ACP100X175SB
| ACP | DIN compact cylinder (double-acting, discontinued). |
|---|---|
| 100 | Bore size in mm. |
| ×175 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACP Compact Cylinder ACP100X175SB Is Used
Heavy stamping die clamp
With 3927 N push at 0.5 MPa, the 100 mm bore clamps large automotive stamping dies in a press loader, and the short body slots into the die cart where a full-length profile cylinder cannot reach.
Pallet gate actuator
The 175 mm stroke swings heavy pallet-line gates and stops, while the male rod thread (B code) accepts a clevis knuckle for the pivoting gate arm.
Replacing the Airtac ACP Compact Cylinder ACP100X175SB with the ACE100X175SB
At 100 mm bore this is the top of the ACP range: 3927 N push at 0.5 MPa, against 2513 N for the 80 mm bore and 1558.6 N for the 63 mm bore. If your load needs under 2500 N, the 80 mm size saves space; if you are near the limit at 0.5 MPa, remember the 5497.8 N available at 0.7 MPa. The 175 mm stroke sits inside the 300 mm maximum standard stroke for this bore. Choose LB foot or FA/FB flange mounting for fixed frames, CA/CB clevis for pivoting links, and keep the -S magnet code if CMSE/DMSE switches are planned. A plain cylinder drifts when air is lost, so add a rod lock or pilot check valve for held loads. Order ACE100X175 as the current replacement and verify ISO 21287 hole patterns first.
Replacement checklist
- ✓ Current-production ACE → ACE100X175SB
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACP Compact Cylinder ACP100X175SB FAQ
At 0.5 MPa it pushes 3927 N and pulls 3681.6 N; at 0.7 MPa push rises to 5497.8 N and pull to 5154.2 N, with a theoretical maximum of 800.9 kgf at 1.0 MPa. The model is discontinued; the current-production replacement is ACE100X175 in the same bore, stroke and force class - confirm the ISO 21287 mounting dimensions before swapping.
It uses a hard-anodized aluminium body with threaded aluminium covers, a 25 mm S45C hard-chrome rod with male thread, 1/4" ports and fixed TPU bumpers at both ends. This unit includes the optional -S magnet, so CMSE or DMSE reed or solid-state switches can be mounted for position feedback. Operating range is 0.15-1.0 MPa (22-145 psi), speed 30-500 mm/s, temperature -20 to +70 C.
Related AirTAC ACE Cylinders
Request a Quote for the ACE100X175SB
Send us the quantity and destination. We confirm price, stock and lead time on the ACE100X175SB replacement — usually within 7-8 hours.