This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACE63X10B, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACP Compact Cylinder ACP63X10B
The AirTAC ACP Compact Cylinder ACP63X10B is a double acting DIN-standard tight/compact air cylinder with a Ø63mm bore and 10mm stroke, 1/8" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACE63X10B (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ63 mm
- Stroke10 mm
- Port size1/8"
- Acting typeDouble acting
- Rod threadM10×1.5
- StatusDiscontinued → ACE63X10B
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACP Compact Cylinder ACP63X10B
A double acting compact cylinder in the DIN-standard ACP series, the ACP63X10B delivers 1558.6 N of push force and 1458.1 N of pull force at 0.5 MPa, rising to 2182.1 N at 0.7 MPa. The 10 mm stroke suits short-clamp and press-fit motions, and the male rod thread (B code) with a 16 mm rod bolts straight to standard knuckles. Air supply is 0.15-1.0 MPa (22-145 psi), speed runs 30-500 mm/s, and the port is 1/8".
The short ISO 21287-class body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight fixtures and guarded cells. Fixed TPU bumpers sit at both ends, the body is hard-anodized aluminium with an S45C hard-chrome rod, and this model is discontinued - the current direct is ACE63X10, so confirm ISO 21287 mounting dimensions before swapping.
Airtac ACP Compact Cylinder ACP63X10B Technical Specifications
| Model | Airtac ACP Compact Cylinder ACP63X10B |
|---|---|
| Series | ACP DIN compact cylinder (discontinued) |
| Replacement | ACE63X10B |
| Bore size | Ø63 mm |
| Stroke | 10 mm |
| Acting type | Double acting |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 250 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACE63X10B (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1458 N |
| 0.7 MPa | 2182 N | 2041 N |
| Max (@1.0 MPa) | 318 kgf | |
The ACE63X10B produces the same force from the same bore. Actual usable force is lower than theoretical; size with a margin.
Model Code: Airtac ACP Compact Cylinder ACP63X10B
| ACP | DIN compact cylinder (double-acting, discontinued). |
|---|---|
| 63 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACP Compact Cylinder ACP63X10B Is Used
Short-stroke press fitting
With 1558.6 N push at 0.5 MPa over just 10 mm, it presses bearings or bushings into aluminium housings on an assembly bench where full-length cylinders cannot fit.
Fixture clamping in machining cells
The male rod thread and compact body make it a direct clamp actuator on CNC jigs, holding machined parts against locators through the 10 mm clamp travel.
Case hold-down on packing lines
Mounted above a conveyor, the 63 mm bore holds cartons steady during taping or labelling, with the short body clearing low guarding.
Replacing the Airtac ACP Compact Cylinder ACP63X10B with the ACE63X10B
At 63 mm bore this sits in the mid-heavy force band: step down to a 50 mm bore for 981.7 N push at 0.5 MPa, or up to 80 mm for 2513.3 N if the clamp needs more muscle. The 10 mm stroke is well inside the 250 mm maximum standard stroke for this bore. Note that a plain cylinder of this type drifts when air is lost - add a rod lock or pilot check valve if the load must stay put. This unit has no magnet; order the -S code if you later need CMSE or DMSE switch positions. For new builds, specify ACE63X10 instead.
Replacement checklist
- ✓ Current-production ACE → ACE63X10B
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACP Compact Cylinder ACP63X10B FAQ
At 0.5 MPa it pushes 1558.6 N and pulls 1458.1 N; at 0.7 MPa that rises to 2182.1 N push and 2041.3 N pull. The theoretical maximum is 317.9 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof pressure.
Order ACE63X10, the current-production ISO 21287 successor: swap the P for an E and you get the same 63 mm bore, 10 mm stroke and force class in a matching short body. Because the ACP was built to a DIN standard, confirm the ISO 21287 mounting dimensions against your fixture before the swap. FA/FB flange, LB foot and CA/CB clevis options carry over in the ACE family.
Request a Quote for the ACE63X10B
Send us the quantity and destination. We confirm price, stock and lead time on the ACE63X10B replacement — usually within 7-8 hours.