This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACE80X125B, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACP Compact Cylinder ACP80X125B
The AirTAC ACP Compact Cylinder ACP80X125B is a double acting DIN-standard tight/compact air cylinder with a Ø80mm bore and 125mm stroke, 1/4" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACE80X125B (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ80 mm
- Stroke125 mm
- Port size1/4"
- Acting typeDouble acting
- Rod threadM12×1.75
- StatusDiscontinued → ACE80X125B
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACP Compact Cylinder ACP80X125B
The ACP80X125B is a double acting DIN-standard compact cylinder with an 80 mm bore and 125 mm stroke, driving a 20 mm hard-chrome S45C rod from a hard-anodized aluminium body. At 0.5 MPa it pushes 2513.3 N and pulls 2356.2 N, rising to 3518.6 N on extension at 0.7 MPa, with a theoretical ceiling of 512.6 kgf at 1.0 MPa. Its short ISO 21287-class body saves roughly half the mounting length of an ISO 15552 profile cylinder, which is why it slots into presses and gantries where a full-length body simply will not fit.
The male rod thread (B code) suits knuckle and tooling attachments, ports are 1/4" PT, and fixed TPU bumpers decelerate the piston at each end. Note this model is discontinued; the current direct is ACE80X125, so confirm ISO 21287 mounting dimensions before swapping.
Airtac ACP Compact Cylinder ACP80X125B Technical Specifications
| Model | Airtac ACP Compact Cylinder ACP80X125B |
|---|---|
| Series | ACP DIN compact cylinder (discontinued) |
| Replacement | ACE80X125B |
| Bore size | Ø80 mm |
| Stroke | 125 mm |
| Acting type | Double acting |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACE80X125B (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2356 N |
| 0.7 MPa | 3519 N | 3299 N |
| Max (@1.0 MPa) | 513 kgf | |
The ACE80X125B produces the same force from the same bore. Actual usable force is lower than theoretical; size with a margin.
Model Code: Airtac ACP Compact Cylinder ACP80X125B
| ACP | DIN compact cylinder (double-acting, discontinued). |
|---|---|
| 80 | Bore size in mm. |
| ×125 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACP Compact Cylinder ACP80X125B Is Used
Pneumatic press head
A 2513.3 N push at 0.5 MPa suits a bench-top forming or staking press on aluminium brackets, with the 125 mm stroke clearing the part by hand.
Pallet gate actuator
The short body fits inside conveyor guarding to swing a heavy stop gate, saving about 50% of the length an ISO 15552 profile cylinder would need.
Replacing the Airtac ACP Compact Cylinder ACP80X125B with the ACE80X125B
At this force class, compare against neighbours: a 63 mm bore gives 1558.6 N push at 0.5 MPa, while a 100 mm bore reaches 3927.0 N, so the 80 mm sits squarely in the mid-heavy range for clamping and pressing. If the load must stay put when air is lost, add a rod lock or pilot check valve - the bumper will not hold position. Foot (LB), flange (FA/FB) and clevis (CA/CB) mounts bolt to the standard face, and CMSE / DMSE switches work only when the optional -S magnet is ordered (this code has none). Since ACP is discontinued, order ACE80X125 as the current-production equivalent and verify the ISO 21287 hole pattern first.
Replacement checklist
- ✓ Current-production ACE → ACE80X125B
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACP Compact Cylinder ACP80X125B FAQ
At 0.5 MPa it pushes 2513.3 N and pulls 2356.2 N; at 0.7 MPa push rises to 3518.6 N; theoretical maximum is 512.6 kgf at 1.0 MPa. It is double acting, runs 0.15-1.0 MPa (22-145 psi) with 1.5 MPa (215 psi) proof pressure, moves at 30-500 mm/s, and ports are 1/4" PT on the 80 mm bore.
The ACE80X125 is the current ISO 21287 successor in the same bore, stroke and force class. The ACP itself is a short-body compact cylinder with a hard-anodized aluminium body, S45C hard-chrome rod, fixed TPU bumpers and FA/FB, LB or CA/CB mounting; the magnet is the optional -S code for CMSE / DMSE switches. Confirm the ISO 21287 mounting dimensions before swapping.
Related AirTAC ACE Cylinders
Request a Quote for the ACE80X125B
Send us the quantity and destination. We confirm price, stock and lead time on the ACE80X125B replacement — usually within 7-8 hours.