This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACE80X150SB, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACP Compact Cylinder ACP80X150SB
The AirTAC ACP Compact Cylinder ACP80X150SB is a double acting DIN-standard tight/compact air cylinder with a Ø80mm bore and 150mm stroke, 1/4" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACE80X150SB (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ80 mm
- Stroke150 mm
- Port size1/4"
- Acting typeDouble acting
- Rod threadM12×1.75
- StatusDiscontinued → ACE80X150SB
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACP Compact Cylinder ACP80X150SB
A double acting compact cylinder in the discontinued AirTAC ACP series, the ACP80X150SB pairs an 80 mm bore with a 150 mm stroke and a 20 mm male-threaded rod (the B code). At 0.5 MPa it pushes 2513.3 N and pulls 2356.2 N; at 0.7 MPa those rise to 3518.6 N and 3298.7 N, with a theoretical ceiling of 512.6 kgf at 1.0 MPa. The short ISO 21287-class body saves roughly 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into presses, gantries and machine frames where a full-length body will not fit.
Air supply is 0.15-1.0 MPa (22-145 psi) with 1.5 MPa (215 psi) proof pressure, speed runs 30-500 mm/s, and the hard-anodized aluminium body carries a fixed TPU bumper at both ends. The S code means the optional -S magnet is fitted, so CMSE or DMSE reed and solid-state switches can be mounted directly on the body. This model is discontinued: the current-production direct is ACE80X150, and buyers should confirm the ISO 21287 mounting dimensions before swapping, since the ACP was built to a DIN standard.
Airtac ACP Compact Cylinder ACP80X150SB Technical Specifications
| Model | Airtac ACP Compact Cylinder ACP80X150SB |
|---|---|
| Series | ACP DIN compact cylinder (discontinued) |
| Replacement | ACE80X150SB |
| Bore size | Ø80 mm |
| Stroke | 150 mm |
| Acting type | Double acting |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACE80X150SB (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2356 N |
| 0.7 MPa | 3519 N | 3299 N |
| Max (@1.0 MPa) | 513 kgf | |
The ACE80X150SB produces the same force from the same bore. Actual usable force is lower than theoretical; size with a margin.
Model Code: Airtac ACP Compact Cylinder ACP80X150SB
| ACP | DIN compact cylinder (double-acting, discontinued). |
|---|---|
| 80 | Bore size in mm. |
| ×150 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACP Compact Cylinder ACP80X150SB Is Used
Pneumatic press stamping
A short-stroke marking or riveting press on an electronics assembly line, where 2513.3 N of push at 0.5 MPa is enough for aluminium tags and the compact body fits inside the press frame.
Pallet gate actuator
Swinging a heavy safety gate or stopper arm on a warehouse conveyor line; the 150 mm stroke clears the aisle and the 1/4" port keeps flow losses low at 30-500 mm/s.
Vertical part lift fixture
Raising cast aluminium housings of about 120 kg between machining stations, using the roughly 128 kg vertical-lift margin and a pilot check valve to hold position on air loss.
Replacing the Airtac ACP Compact Cylinder ACP80X150SB with the ACE80X150SB
At this force level, compare both neighbours: a 63 mm bore delivers 1558.6 N push at 0.5 MPa, while a 100 mm bore reaches 3927.0 N - the 80 mm sits between them with 2513.3 N. If the load must stay put when air is lost, add a rod lock or pilot check valve, because the piston will drift once the valve centres. The male rod thread (B) suits rod knuckles and tooling plates; FA/FB flange, LB foot and CA/CB clevis mountings bolt to the same face. Stroke 150 mm is within the 300 mm standard range for this bore. Order ACE80X150 as the current replacement and verify ISO 21287 mounting dimensions first.
Replacement checklist
- ✓ Current-production ACE → ACE80X150SB
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACP Compact Cylinder ACP80X150SB FAQ
At 0.5 MPa it pushes 2513.3 N and pulls 2356.2 N; at 0.7 MPa push is 3518.6 N and pull is 3298.7 N. The theoretical maximum is 512.6 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi) with 1.5 MPa (215 psi) proof pressure, and speed is 30-500 mm/s.
The hard-anodized aluminium body is a short ISO 21287-class design, about 50% shorter in mounting length than an ISO 15552 profile cylinder, with a fixed TPU bumper at each end. The S in the model code means the optional -S magnet is fitted, so CMSE or DMSE reed and solid-state switches can be clamped to the body; without the -S code there is no magnet. The ACP80X150SB itself is discontinued - the current-production direct is ACE80X150 in the same bore, stroke and force class, but confirm the ISO 21287 mounting dimensions before swapping because the ACP followed a DIN standard.
Related AirTAC ACE Cylinders
Request a Quote for the ACE80X150SB
Send us the quantity and destination. We confirm price, stock and lead time on the ACE80X150SB replacement — usually within 7-8 hours.