
The AirTAC ACQJ32~40 Adjustable Thin-Type Cylinder ACQJ40X30-20SFA is a genuine double-acting COMPACT (JIS) cylinder with an EXTERNAL adjustable stop on the extend stroke — a Ø40mm bore and 30mm full stroke. Turn the stop to fine-tune the end position on the machine without changing parts.
The ACQJ40X30-20SFA is a double-acting JIS compact cylinder with a 40 mm bore and an external threaded stop that limits the extend stroke. You can fine-tune the usable extend range from 10 mm up to the full 30 mm directly on your equipment, while the retract distance remains completely unaffected. It includes a built-in piston magnet for position sensing and an FA mounting bracket interface.
Because the adjuster only restricts travel length, the piston area stays the same, meaning force is identical to a standard ACQ. The body uses fixed NBR elastomer bumpers at both ends for end-of-stroke deceleration rather than adjustable air cushions.
| Model | Airtac ACQJ32~40 Adjustable Thin-Type Cylinder ACQJ40X30-20SFA |
|---|---|
| Series | ACQJ JIS compact adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Full stroke | 30 mm |
| Adjuster thread | M12×1.25 |
| Port size | PT1/8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Rod thread | M8×1.25 (F) / M14×1.5 (B) |
Specifications follow the official AirTAC ACQJ datasheet. The adjustable stop shortens the EXTEND stroke only; ACQJ is double-rod, so push is lower than a standard ACQ of this bore. Adjustable window options: 10/20/30/40/50/75/100 mm.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
ACQJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod ACQ push of the same bore. Actual usable force is lower due to friction; size with a safety margin.
| ACQJ | JIS compact double-acting ADJUSTABLE-STROKE cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×30 | Full stroke length in mm. |
| -0 | Adjustable window in mm (extend stroke can be shortened by up to this). |
| S / B | Magnet (S) / male-thread rod (B); omit for none / female thread. |
Thread: PT standard (G / NPT available). Related: ACQ (fixed stroke), ACQD (double rod), TACQ (guided / non-rotating).
Adjust the extend stop by up to 20 mm during packaging line changeovers to hit new product widths without swapping cylinders.
Dial in the exact 10 to 30 mm clamping extension on assembly fixtures during prototype runs to prevent over-travel damage.
Fine-tune the extend endpoint on machining jigs to accommodate varying part tolerances directly on the factory floor.
Stepping down to a 32 mm bore yields 402.1 N, whereas moving up to a 50 mm bore provides 981.8 N. Choose this specific unit when your setup requires exact extend end-position tuning within a 10-30 mm window. If your application does not need on-the-fly stroke shortening, a fixed-stroke ACQ cylinder is sufficient. Confirm your ordering essentials: 40 mm bore, 30 mm full stroke, 20 mm adjuster window, S magnet, female M8x1.25 rod end, and FA mount.
AirtacDistr lists every ACQJ40 order code with its price on one page at https://airtacdistr.com/products/airtac-acqj40-adjustable-cylinder
Quick checklist
The usable extend range is 10-30 mm (a 20 mm window off the 30 mm full stroke).
An external M12x1.25 threaded stop with a lock nut limits the extend stroke only; retract is unaffected, and force is unchanged. The cylinder uses fixed NBR bumpers, not an air cushion. Note that a plain ACQ-type does not hold its load on air loss, so use an external rod lock for fail-safe holding.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.