This model is discontinued
AirTAC has phased out the MAL series. The drop-in replacement is ATE80X10SB — same bore, stroke, output force, port and mounting, so it fits the same application. Simply order the ATE80X10SB in place of this model. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ATP Single Acting Port Compact Cylinder ATP80X10SB
The AirTAC Airtac ATP Single Acting Port Compact Cylinder ATP80X10SB is a single acting, pull (spring return) DIN-standard tight/compact air cylinder with a Ø80mm bore and 10mm stroke, 1/4" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ATE80X10SB (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ80 mm
- Stroke10 mm
- Port size1/4"
- Acting typeSingle acting, pull (spring return)
- Rod threadM12×1.75
- StatusDiscontinued → ATE80X10SB
About the Airtac ATP Single Acting Port Compact Cylinder ATP80X10SB
The ATP80X10SB is a single acting pull cylinder of DIN-standard compact design: a spring extends the 20 mm rod and compressed air retracts it, so the unit rests normally extended and fails to the extended position when air is lost. At 0.5 MPa it delivers 2159.1 N of pull net of the spring (3101.6 N at 0.7 MPa), which works out to roughly 1295 N of usable force if you plan at 60% of rating - about 110 kg lifted vertically with a 2:1 margin. Minimum working pressure is 0.2 MPa (28 psi) to overcome the spring, within a 0.2-1.0 MPa (28-145 psi) band.
The hard-anodized aluminium body with an S45C hard-chrome rod saves about 50% of the mounting length of an ISO 15552 profile cylinder, so an 80 mm bore fits clamping stations and press fixtures too tight for a full-length body. This model carries the optional -S magnet, so CMSE or DMSE reed and solid-state switches can be mounted for end-of-stroke signalling, and the B code gives a male rod thread with a 1/4" PT port. Note the ATP family is discontinued - the current-production drop-in is the ATE80X10, so confirm ISO 21287 mounting dimensions before you swap.
Airtac ATP Single Acting Port Compact Cylinder ATP80X10SB Technical Specifications
| Model | Airtac ATP Single Acting Port Compact Cylinder ATP80X10SB |
|---|---|
| Series | ATP DIN compact cylinder (discontinued) |
| Replacement | ATE80X10SB |
| Bore size | Ø80 mm |
| Stroke | 10 mm |
| Acting type | Single acting, pull (spring return) |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.2 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 25 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ATE80X10SB (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø80mm)
| Pressure | Pull force (spring return) |
|---|---|
| 0.5 MPa | 2159.1 N |
| 0.7 MPa | 3101.6 N |
Single-acting pull: the spring extends the rod; air retracts it. Forces already net the spring; minimum working pressure is 0.2 MPa.
Model Code: Airtac ATP Single Acting Port Compact Cylinder ATP80X10SB
| ATP | DIN compact cylinder (single-acting pull, spring-return, discontinued). |
|---|---|
| 80 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (adjustable stroke).
Where the Airtac ATP Single Acting Port Compact Cylinder ATP80X10SB Is Used
Fixture retraction on a CNC pallet clamp
The spring holds the clamp open and air pulls the 20 mm rod to release a machined housing; 2159.1 N at 0.5 MPa handles the wedge linkage without a larger bore.
Slide return on an automotive checking station
Normally-extended behaviour means a lost-air fault leaves the gauge slide retracted home, and the fitted -S magnet with a DMSE switch signals the retracted position to the PLC.
Tray hold-down release on a carton erecting line
A short 10 mm pull lifts the hold-off pin between carton cycles at 50-500 mm/s, and the fixed TPU bumpers quiet the ends of travel in a tight frame.
Replacing the Airtac ATP Single Acting Port Compact Cylinder ATP80X10SB with the ATE80X10SB
Size the bore against your real pull need: at 0.5 MPa the 63 mm bore gives 1320.0 N while this 80 mm bore gives 2159.1 N, and the 100 mm bore reaches 3395.3 N if you need more. Keep the 10 mm stroke short - it is well inside the standard range for this bore - and remember the spring only returns the rod to its extended home, it will not hold a mid-stroke position. FA/FB flange, LB foot and CA/CB clevis mounts bolt to the same face family, and the -S magnet is already fitted on this code. Order the ATE80X10 as the current replacement.
Replacement checklist
- ✓ Current-production ACE → ATE80X10SB
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ATP Single Acting Port Compact Cylinder ATP80X10SB FAQ
Pull is 2159.1 N at 0.5 MPa and 3101.6 N at 0.7 MPa, both net of the return spring, with a minimum of 0.2 MPa needed to move the rod. For sizing, treat about 1295 N (60% of the 0.5 MPa figure) as the working force, which lifts roughly 110 kg vertically with a 2:1 margin. Operating range is 0.2-1.0 MPa (28-145 psi), proof 1.5 MPa (215 psi), speed 50-500 mm/s, air filtered to 40 um, -20 to +70 C.
No - the ATP family is discontinued. The current-production drop-in is the ATE80X10 (same P-to-E swap), which matches the 80 mm bore, 10 mm stroke and force class in the ISO 21287 short-body format. Because the ATP was built to a DIN-standard compact outline, confirm the ISO 21287 mounting dimensions and your FA/FB, LB or CA/CB bracket fit before swapping.
Related AirTAC ACE Cylinders
Request a Quote for the ATE80X10SB
Send us the quantity and destination. We confirm price, stock and lead time on the ATE80X10SB replacement — usually within 7-8 hours.