This model is discontinued
AirTAC has phased out the MAL series. The drop-in replacement is ATE80X5S — same bore, stroke, output force, port and mounting, so it fits the same application. Simply order the ATE80X5S in place of this model. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ATP Single Acting Port Compact Cylinder ATP80X5S
The AirTAC Airtac ATP Single Acting Port Compact Cylinder ATP80X5S is a single acting, pull (spring return) DIN-standard tight/compact air cylinder with a Ø80mm bore and 5mm stroke, 1/4" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ATE80X5S (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ80 mm
- Stroke5 mm
- Port size1/4"
- Acting typeSingle acting, pull (spring return)
- Rod threadM12×1.75
- StatusDiscontinued → ATE80X5S
About the Airtac ATP Single Acting Port Compact Cylinder ATP80X5S
A single acting pull cylinder with spring extend, the ATP80X5S keeps the rod normally out and uses compressed air to retract it over a short 5 mm stroke. At 0.5 MPa the net pull is 2159.1 N (3101.6 N at 0.7 MPa), already deducted for the return spring, so the numbers you see are the numbers you clamp with. The 80 mm bore takes a 1/4" port and an M12x1.75 female rod thread, and the S code means the magnet is fitted, so CMSE or DMSE switches can be mounted for end-of-stroke signalling.
The short ISO 21287-class body saves roughly 50% of the mounting length of an ISO 15552 profile cylinder, which is why it slots into tight fixtures and guarding where a full-length body will not go. For sizing, treat about 1295 N (roughly 0.6 of the 0.5 MPa pull) as the realistic working force, which lifts about 110 kg vertically with a 2:1 margin. Note this model is discontinued: the current-production replacement is the ATE80X5, so confirm ISO 21287 mounting dimensions before swapping.
Airtac ATP Single Acting Port Compact Cylinder ATP80X5S Technical Specifications
| Model | Airtac ATP Single Acting Port Compact Cylinder ATP80X5S |
|---|---|
| Series | ATP DIN compact cylinder (discontinued) |
| Replacement | ATE80X5S |
| Bore size | Ø80 mm |
| Stroke | 5 mm |
| Acting type | Single acting, pull (spring return) |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.2 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 25 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ATE80X5S (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø80mm)
| Pressure | Pull force (spring return) |
|---|---|
| 0.5 MPa | 2159.1 N |
| 0.7 MPa | 3101.6 N |
Single-acting pull: the spring extends the rod; air retracts it. Forces already net the spring; minimum working pressure is 0.2 MPa.
Model Code: Airtac ATP Single Acting Port Compact Cylinder ATP80X5S
| ATP | DIN compact cylinder (single-acting pull, spring-return, discontinued). |
|---|---|
| 80 | Bore size in mm. |
| ×5 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (adjustable stroke).
Where the Airtac ATP Single Acting Port Compact Cylinder ATP80X5S Is Used
Spring-out clamping of machined housings
The normally extended rod holds an aluminium gearbox housing against a fixture; air retraction at 0.5 MPa gives 2159.1 N of pull for fast release between cycles on a CNC line.
Ejector on a stamping die
A 5 mm kick-off stroke clears thin pressed brackets from the die face; the spring pushes the ejector plate out the moment air pressure drops, a natural fail-safe at the press.
Position-flagged gate on a packaging line
With the fitted magnet and a DMSE switch, the PLC confirms the gate is in its extended home position before the filler head advances, at speeds up to 500 mm/s.
Replacing the Airtac ATP Single Acting Port Compact Cylinder ATP80X5S with the ATE80X5S
Size by force first: at 0.5 MPa this 80 mm bore nets 2159.1 N of pull, while a 63 mm bore gives 1320 N and a 100 mm bore reaches 3395.3 N in the same family. The spring returns the rod to its extended home on air loss and will not hold a mid-stroke position, so add an external stop if you need one. FA/FB flange, LB foot and CA/CB clevis mountings bolt to the same face, and the fitted -S magnet accepts CMSE / DMSE switches. Order the ATE80X5 as the current drop-in successor.
Replacement checklist
- ✓ Current-production ACE → ATE80X5S
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ATP Single Acting Port Compact Cylinder ATP80X5S FAQ
Net of the return spring, the 80 mm bore pulls 2159.1 N at 0.5 MPa and 3101.6 N at 0.7 MPa. Minimum working pressure is 0.2 MPa (28-145 psi operating range, 1.5 MPa / 215 psi proof). It runs on air filtered to 40 um, handles -20 to +70 C, and cycles at 50-500 mm/s over the 5 mm stroke.
The hard-anodized aluminium body with S45C hard-chrome rod is an ISO 21287-class short build, saving about 50% of the mounting length of an ISO 15552 profile cylinder, with fixed TPU bumpers at both ends. The ATP family is discontinued; the ATE80X5 is the current-production drop-in in the same bore, stroke and force class, so confirm the ISO 21287 mounting dimensions before you swap.
Request a Quote for the ATE80X5S
Send us the quantity and destination. We confirm price, stock and lead time on the ATE80X5S replacement — usually within 7-8 hours.