This model is discontinued
AirTAC has phased out the MAL series. The drop-in replacement is ATE80X5SB — same bore, stroke, output force, port and mounting, so it fits the same application. Simply order the ATE80X5SB in place of this model. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ATP Single Acting Port Compact Cylinder ATP80X5SB
The AirTAC Airtac ATP Single Acting Port Compact Cylinder ATP80X5SB is a single acting, pull (spring return) DIN-standard tight/compact air cylinder with a Ø80mm bore and 5mm stroke, 1/4" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ATE80X5SB (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ80 mm
- Stroke5 mm
- Port size1/4"
- Acting typeSingle acting, pull (spring return)
- Rod threadM12×1.75
- StatusDiscontinued → ATE80X5SB
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ATP Single Acting Port Compact Cylinder ATP80X5SB
A single acting, spring-extend pull cylinder built to the DIN-standard compact format, the ATP80X5SB keeps its 80 mm bore inside a short hard-anodized aluminium body that saves roughly 50% of the mounting length of an ISO 15552 profile cylinder. The spring holds the rod out; air between 0.2 MPa and 1.0 MPa (28-145 psi) retracts it, delivering 2159.1 N of pull at 0.5 MPa (3101.6 N at 0.7 MPa), both figures already net of the spring. This model carries the optional -S magnet, so CMSE or DMSE reed and solid-state switches can be clipped on for end-of-stroke sensing, and the B code gives a male rod thread with a 1/4" port.
Note that the ATP family is discontinued; the current-production drop-in is the ATE80X5, which keeps the same bore, stroke and force class. Confirm the ISO 21287 mounting dimensions before swapping. For sizing, treat about 1295 N as the realistic working pull at 0.5 MPa, which corresponds to lifting roughly 66 kg vertically with a 2:1 margin - enough to reseat a heavy press tooling lid or release a clamped fixture. A fixed TPU bumper at each end decelerates the rod, and the 20 mm S45C hard-chrome rod runs at 50-500 mm/s.
Airtac ATP Single Acting Port Compact Cylinder ATP80X5SB Technical Specifications
| Model | Airtac ATP Single Acting Port Compact Cylinder ATP80X5SB |
|---|---|
| Series | ATP DIN compact cylinder (discontinued) |
| Replacement | ATE80X5SB |
| Bore size | Ø80 mm |
| Stroke | 5 mm |
| Acting type | Single acting, pull (spring return) |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.2 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 25 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ATE80X5SB (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø80mm)
| Pressure | Pull force (spring return) |
|---|---|
| 0.5 MPa | 2159.1 N |
| 0.7 MPa | 3101.6 N |
Single-acting pull: the spring extends the rod; air retracts it. Forces already net the spring; minimum working pressure is 0.2 MPa.
Model Code: Airtac ATP Single Acting Port Compact Cylinder ATP80X5SB
| ATP | DIN compact cylinder (single-acting pull, spring-return, discontinued). |
|---|---|
| 80 | Bore size in mm. |
| ×5 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (adjustable stroke).
Where the Airtac ATP Single Acting Port Compact Cylinder ATP80X5SB Is Used
Press tooling unclamp
The 2159.1 N spring-extended pull retracts a locking pin on a stamping die set the moment air is applied, and the 5 mm stroke is all a latch needs to clear.
Fixture gate release
On a machining-centre pallet fixture, air applied at 0.5 MPa pulls a heavy swing gate open; loss of air leaves the gate spring-held closed for operator safety.
Battery changeover latch
In warehouse forklift charging bays, the 80 mm bore pulls a spring-loaded battery-retention hook open; about 66 kg of vertical margin covers the hook's resistance.
Replacing the Airtac ATP Single Acting Port Compact Cylinder ATP80X5SB with the ATE80X5SB
At 80 mm bore this is the second-strongest ATP size: 2159.1 N of pull at 0.5 MPa versus 3395.3 N from the 100 mm bore, while the 63 mm bore gives 1320.0 N if your load is lighter. The 5 mm stroke suits retraction-only tasks such as unclamping or part release, and the spring returns the rod to its extended home on air loss - it will not hold a mid-stroke position. Mount with FA/FB flange, LB foot or CA/CB clevis brackets, and remember the -S magnet on this unit enables CMSE / DMSE switch feedback. Since the ATP is discontinued, order the ATE80X5 as the current ISO 21287 replacement and verify mounting dimensions against your fixture.
Replacement checklist
- ✓ Current-production ACE → ATE80X5SB
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ATP Single Acting Port Compact Cylinder ATP80X5SB FAQ
This is a single acting pull cylinder: the spring extends the rod and air retracts it. Pull force is 2159.1 N at 0.5 MPa and 3101.6 N at 0.7 MPa, both net of the return spring. Working pressure is 0.2-1.0 MPa (28-145 psi), proof pressure 1.5 MPa (215 psi), minimum 0.2 MPa to overcome the spring, speed 50-500 mm/s, temperature -20 to +70 C, and the 1/4" port matches the 80 mm bore.
The short DIN-standard compact body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits tight guards and gantries. The ATP family is discontinued; the ATE80X5 is the current-production ISO 21287 drop-in with the same 80 mm bore, 5 mm stroke and force class - confirm the mounting dimensions before swapping. This unit carries the optional -S magnet for CMSE / DMSE switches and a fixed TPU bumper at both ends.
Request a Quote for the ATE80X5SB
Send us the quantity and destination. We confirm price, stock and lead time on the ATE80X5SB replacement — usually within 7-8 hours.