Airtac B01-MAC Series Special Purpose Cylinder B01-MAC63X200SCA
The AirTAC Airtac B01-MAC Series Special Purpose Cylinder B01-MAC63X200SCA is a genuine double acting + cushion standard round-body mini air cylinder with a Ø0mm bore and 200mm stroke, PT/G air ports and a stainless-steel barrel with a hard-chrome-plated rod for reliable, mildly corrosion-resistant service. A variable air cushion at both ends lets you tune end-of-stroke deceleration on site.
- BoreØ0 mm
- Stroke200 mm
- Port sizePT/G
- Acting typeDouble acting + cushion
- Rod thread
- CushionVariable air cushion, both ends
About the Airtac B01-MAC Series Special Purpose Cylinder B01-MAC63X200SCA
With 200 mm of travel and the largest bore AirTAC builds in this series, MAC63X200SCA moves serious work: 1557.9 N forward and 1457.4 N back at 0.5 MPa, rising to 2181.0 N at 0.7 MPa. Both chambers are air fed, and variable cushions absorb the arrival shock at each end of the long stroke.
A 200 mm stroke amplifies any side load, so the hard-chrome plated 16 mm rod expects its work guided outside the cylinder. The riveted stainless body rides out humidity and light chemical splash that pit painted minis within a season. The CA pivot cover swings on a yoke or clevis, or order the U / CM cover when a fixed face fits the frame. Lifting maths: the 1557.9 N push equals about 159 kg of weight, so keeping a 2:1 margin puts roughly 79 kg as a sensible vertical lift.
Airtac B01-MAC Series Special Purpose Cylinder B01-MAC63X200SCA Technical Specifications
| Model | Airtac B01-MAC Series Special Purpose Cylinder B01-MAC63X200SCA |
|---|---|
| Series | MAC mini cylinder |
| Bore size | Ø0 mm |
| Stroke | 200 mm |
| Acting type | Double acting + cushion |
| Port size | PT/G |
| Rod thread |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MA-series datasheet. Barrel: stainless-steel tube (round-body, riveted rolling-packed construction); piston rod: carbon steel with 20µm hard-chrome plating; covers: aluminium alloy. Thread options: PT (blank) / G / NPT. Every MA-series cylinder ships with a built-in magnet for CMSG / DMSG / EMSG position sensors.
Theoretical Output Force (Ø0mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 0 N | 0 N |
| 0.7 MPa | 0 N | 0 N |
| Max (@1.0 MPa) | 0 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac B01-MAC Series Special Purpose Cylinder B01-MAC63X200SCA
| MAC | Standard round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 0 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -S | Built-in magnet for CMSG / DMSG / EMSG sensors (standard on MA series). |
| CA / U / CM | Back-cover type: CA pivot, U flat-end, CM round-end. |
MA-family variants: MA / MAC (double acting ±cushion), MSA / MTA (single acting push / pull), MAD / MACD (double rod ±cushion), MAJ / MACJ (adjustable stroke ±cushion), MAR (cushioned with integrated F/U mount). Mounting accessories: FA flange, LB foot, SDB pivot; plus I and Y knuckles. Thread PT (blank) / G / NPT.
Where the Airtac B01-MAC Series Special Purpose Cylinder B01-MAC63X200SCA Is Used
Ingot quench pusher
Advances 75 kg aluminum ingots 200 mm off a casting conveyor into the quench chute; cushioning tames the load arriving at the stop.
Coil wrap tension arm
Presses a lever that tensions stretch film on a steel coil packaging line, applying about 900 N of practical force at 0.5 MPa.
Feed blender slide gate
Raises a 70 kg slide gate 200 mm to discharge mixed poultry feed; with a 2:1 margin the 159 kg-equivalent thrust lifts it cleanly.
Is the Airtac B01-MAC Series Special Purpose Cylinder B01-MAC63X200SCA the Right Cylinder?
Size on either side: the 50 mm bore gives 981.3 N at 0.5 MPa for lighter gates, while the 63 is the ceiling of the MAC range. The cylinder accepts 0.15-1.0 MPa (22-145 psi) with speeds from 30-800 mm/s, so mid-range pressure settings already produce most of the thrust. Once the valve returns to centre, the piston is free to move - fit a rod lock or pilot check valve whenever the 200 mm stroke carries a suspended or clamped part. FA flange and LB foot brackets suit fixed frames; SDB pivot brackets suit the swinging mount this CA cover implies.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) is standard for sensors
- ✓ Back cover (CA/U/CM) & mount (FA/LB/SDB)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check On first run, back off the cushion screws and release gradually.
- check Installation by qualified personnel per AirTAC docs.
Airtac B01-MAC Series Special Purpose Cylinder B01-MAC63X200SCA FAQ
At 0.5 MPa: 1557.9 N push and 1457.4 N pull. At 0.7 MPa: 2181.0 N push and 2040.3 N pull. The Dia 63 bore reaches a theoretical 317.7 kgf at 1.0 MPa. Air ports are 1/4", the rod thread is M14x1.5, and the 200 mm stroke is a standard catalogue length.
Guide the load externally so the hard-chrome plated 16 mm rod carries pure axial force - long strokes magnify side load and will wear the stainless barrel seals early. The variable cushions at both ends also need setting: start with the needle screws open, then tighten until the 200 mm stroke decelerates cleanly within the 30-800 mm/s speed window.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac B01-MAC Series Special Purpose Cylinder B01-MAC63X200SCA
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.