Airtac HLSL Precision Slide Table Cylinder HLSL20X75SA
The AirTAC Airtac HLSL Precision Slide Table Cylinder HLSL20X75SA is a genuine HLS slide-table cylinder, 20 mm bore: a double-acting dual-rod air cylinder integrated with a cross-roller guide so the table travels straight with high rigidity and low deflection. It delivers about 236 N of push at 0.5 MPa. This is the symmetrical version. A floating joint spares the rod from side torque; the magnet is fitted as standard.
- TypeSlide-table, double acting
- Guidecross-roller guide
- Bore20 mm
- Push thrust @0.5 MPa236 N
- Operating pressure0.15 - 0.7 MPa (22 - 100 psi)
- Port size1/8"
- CushionBumper (+ shock-absorber option)
- Magnet / sensorStandard; CMSH/DMSH/EMSH
- ThreadPT
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac HLSL Precision Slide Table Cylinder HLSL20X75SA
The HLSL20X75SA is the symmetrical cross-roller slide table cylinder with adjustable rubber stoppers fitted at both ends: an AirTAC double-acting, dual-rod cylinder whose integrated cross-roller guide gives the table straight, rigid, low-deflection travel. At bore 20 and 75 mm stroke it delivers moderate-to-higher thrust for its bore class, doubled by the dual-rod layout, and the floating joint keeps side torque off the rods. The adjustable stoppers let you fine-tune the end positions to absorb stroke tolerance in the fixture.
This is a genuine AirTAC part with the magnet fitted as standard; magnetic switches CMSH, DMSH or EMSH mount directly in the slots on the body. Exact thrust, dimensions and allowable load or moment figures come from the datasheet or the on-page specification table - we will confirm them on request.
Airtac HLSL Precision Slide Table Cylinder HLSL20X75SA Technical Specifications
| Model | Airtac HLSL Precision Slide Table Cylinder HLSL20X75SA |
|---|---|
| Type | Slide-table cylinder, double acting, dual rod |
| Series / guide | HLSL (cross-roller guide) |
| Bore | 20 mm |
| Push thrust @0.5 MPa | 236 N |
| Port size | 1/8" (PT thread) |
| Fluid | Air, filtered to 40 um |
|---|---|
| Operating pressure | 0.15 - 0.7 MPa (22 - 100 psi) |
| Proof pressure | 1.2 MPa (175 psi) |
| Temperature | -20 to 70 C |
| Speed range | 50 - 500 mm/s (meter-out) |
| Cushion | Bumper; shock-absorber / adjustable-stopper options |
| Magnet / sensor | Standard; CMSH, DMSH, EMSH |
Specifications follow the official AirTAC HL slide-table data. Max working pressure is 0.7 MPa. The table rides on an integrated linear guide — do not apply strong impact or large moment. Allowable load and moment are published as tables and curves, and overall dimensions vary per stroke — ask us and we confirm from the datasheet.
How to choose
Bore 20 is the choice when a smaller bore in the HLSL range would run out of push; the larger the bore, the higher the thrust, without needing a Newton figure here - the spec table lists it exactly. Stroke 75 mm must appear in the bore-20 stroke table before you commit. Compared with the plain S version, this A version adds adjustable rubber stoppers at both ends, useful when you want cushioning you can tune rather than a fixed bumper; for heavier impact energy look at the B versions with shock absorbers.
Port thread is PT; G and NPT (T) variants are available. Load and moment sizing is published as tables and curves rather than a single number, so route your application load to us and we will verify the selection from the datasheet.
Applications
Assembly stage positioning
Adjustable rubber stoppers at both ends let you trim the 75 mm travel so parts land consistently at the assembly fixture.
Alignment and insertion press
The rigid cross-roller table resists deflection while a pin or bushing is pressed into place under the dual-rod thrust.
Stopper and eject station
Used as a stopper or ejector on a conveyor line, the symmetrical body mounts from either side and the stopper cushions tune the end stop.
FAQ
How does the A in HLSL20X75SA differ from the plain S version?
The A adds adjustable rubber stoppers at both ends, so the end-of-stroke cushioning and exact table stop position can be tuned on the machine. The plain S version has fixed bumpers only. Both share the same cross-roller guide, bore 20, 75 mm stroke and standard magnet.
Can I size the allowable load from the thrust alone?
No. Thrust grows with bore and pressure, but the allowable load, moment and kinetic energy are separate published values in tables and curves for this model. Confirm them from the datasheet or the on-page table before mounting an off-centre or heavy payload.