Airtac HLSL Precision Slide Table Cylinder HLSL25X100S
The AirTAC Airtac HLSL Precision Slide Table Cylinder HLSL25X100S is a genuine HLS slide-table cylinder, 25 mm bore: a double-acting dual-rod air cylinder integrated with a cross-roller guide so the table travels straight with high rigidity and low deflection. It delivers about 378 N of push at 0.5 MPa. This is the symmetrical version. A floating joint spares the rod from side torque; the magnet is fitted as standard.
- TypeSlide-table, double acting
- Guidecross-roller guide
- Bore25 mm
- Push thrust @0.5 MPa378 N
- Operating pressure0.15 - 0.7 MPa (22 - 100 psi)
- Port size1/8"
- CushionBumper (+ shock-absorber option)
- Magnet / sensorStandard; CMSH/DMSH/EMSH
- ThreadPT
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac HLSL Precision Slide Table Cylinder HLSL25X100S
The HLSL25X100S is a symmetrical cross-roller slide table cylinder: a double-acting dual-rod air cylinder with an integrated cross-roller guide that keeps the table on a straight, low-deflection path. The 25 mm bore over a 100 mm stroke gives higher thrust than smaller bores in the range, the dual rods double that push, and the floating joint spares the rods from side torque so the workpiece plate stays aligned.
This is a genuine AirTAC part with the magnet fitted as standard, read by CMSH, DMSH or EMSH sensor switches in the magnetic-switch slots on the body. The body mounts three ways and the workpiece two ways. We confirm exact thrust, dimensions and load-moment ratings from the datasheet or the on-page spec table on request.
Airtac HLSL Precision Slide Table Cylinder HLSL25X100S Technical Specifications
| Model | Airtac HLSL Precision Slide Table Cylinder HLSL25X100S |
|---|---|
| Type | Slide-table cylinder, double acting, dual rod |
| Series / guide | HLSL (cross-roller guide) |
| Bore | 25 mm |
| Push thrust @0.5 MPa | 378 N |
| Port size | 1/8" (PT thread) |
| Fluid | Air, filtered to 40 um |
|---|---|
| Operating pressure | 0.15 - 0.7 MPa (22 - 100 psi) |
| Proof pressure | 1.2 MPa (175 psi) |
| Temperature | -20 to 70 C |
| Speed range | 50 - 500 mm/s (meter-out) |
| Cushion | Bumper; shock-absorber / adjustable-stopper options |
| Magnet / sensor | Standard; CMSH, DMSH, EMSH |
Specifications follow the official AirTAC HL slide-table data. Max working pressure is 0.7 MPa. The table rides on an integrated linear guide — do not apply strong impact or large moment. Allowable load and moment are published as tables and curves, and overall dimensions vary per stroke — ask us and we confirm from the datasheet.
How to choose
Choose the 25 mm bore when you want higher push from the HLSL line; smaller bores are lighter-duty. The cross-roller guide is the precision and rigidity choice, HLQ ball-bearing versions suit anti-rust, dust-proof needs, and HLH/HLF cover miniature and low-height builds. 100 mm is within the bore 25 stroke table. This basic version has no adjuster suffix; rubber-stopper and shock-absorber options (one or both ends) are on the same series. The blank thread position is PT, with G and T available. Route your load and moment sizing to us - figures are published as tables and deflection curves.
Applications
Precision part loading
Feed parts into a fixture over the 100 mm stroke with the cross-roller guide holding the path straight for accurate seating.
Gripper traverse
Traverse a two-finger gripper between pick and place positions; higher bore-25 push suits heavier gripper payloads.
Indexed fixture slide
Index assemblies between stations on the symmetrical table, with EMSH switches confirming each end position.
FAQ
Do I need to order a magnet switch option for position sensing on the HLSL25X100S?
No. The magnet is fitted as standard on every model in this series, so you only choose the switch type - CMSH, DMSH or EMSH - and read it from the magnetic-switch slots on the body.
Can I size the load and moments from the model number alone?
No. Allowable load, moment and kinetic energy are confirmed from the published tables (deflection is published as curves) for this bore and stroke. Send us your workpiece weight and overhang and we will check the datasheet figures with you.