Airtac HLSL Precision Slide Table Cylinder HLSL25X150SA
The AirTAC Airtac HLSL Precision Slide Table Cylinder HLSL25X150SA is a genuine HLS slide-table cylinder, 25 mm bore: a double-acting dual-rod air cylinder integrated with a cross-roller guide so the table travels straight with high rigidity and low deflection. It delivers about 378 N of push at 0.5 MPa. This is the symmetrical version. A floating joint spares the rod from side torque; the magnet is fitted as standard.
- TypeSlide-table, double acting
- Guidecross-roller guide
- Bore25 mm
- Push thrust @0.5 MPa378 N
- Operating pressure0.15 - 0.7 MPa (22 - 100 psi)
- Port size1/8"
- CushionBumper (+ shock-absorber option)
- Magnet / sensorStandard; CMSH/DMSH/EMSH
- ThreadPT
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac HLSL Precision Slide Table Cylinder HLSL25X150SA
The HLSL25X150SA is a symmetrical cross-roller slide table cylinder with a 25 mm bore and 150 mm stroke. Like every model in the HLSL family it is a double-acting, dual-rod cylinder with an integrated cross-roller guide: the table travels straight with high rigidity and low deflection, the two rods double the thrust of a single-piston equivalent, and the floating joint prevents side torque from reaching the rods. The A code adds adjustable rubber stoppers at both ends of the stroke for fine-tuned end positions and gentler impact.
This is a genuine AirTAC part with the position magnet fitted as standard - CMSH, DMSH or EMSH sensor switches clip straight into the magnetic-switch slots on the body. Ports are 1/8 with PT thread on this bore. Exact thrust, dimensions and allowable load and moment values for this specific bore and stroke are published in the specification table and datasheet; we are happy to confirm them for your application on request.
Airtac HLSL Precision Slide Table Cylinder HLSL25X150SA Technical Specifications
| Model | Airtac HLSL Precision Slide Table Cylinder HLSL25X150SA |
|---|---|
| Type | Slide-table cylinder, double acting, dual rod |
| Series / guide | HLSL (cross-roller guide) |
| Bore | 25 mm |
| Push thrust @0.5 MPa | 378 N |
| Port size | 1/8" (PT thread) |
| Fluid | Air, filtered to 40 um |
|---|---|
| Operating pressure | 0.15 - 0.7 MPa (22 - 100 psi) |
| Proof pressure | 1.2 MPa (175 psi) |
| Temperature | -20 to 70 C |
| Speed range | 50 - 500 mm/s (meter-out) |
| Cushion | Bumper; shock-absorber / adjustable-stopper options |
| Magnet / sensor | Standard; CMSH, DMSH, EMSH |
Specifications follow the official AirTAC HL slide-table data. Max working pressure is 0.7 MPa. The table rides on an integrated linear guide — do not apply strong impact or large moment. Allowable load and moment are published as tables and curves, and overall dimensions vary per stroke — ask us and we confirm from the datasheet.
How to choose
Bore 25 is the top of the HLSL thrust range, so this slide suits heavier workpieces and longer 150 mm travels where a smaller bore would run out of push. No newton-level sizing is needed here - just remember bigger bore means more thrust, and the exact figures are in the on-page table for your stroke. Verify that 150 mm appears in the bore 25 stroke table when ordering.
The trailing A specifies adjustable rubber stoppers at both ends; if you need the stronger deceleration of shock absorbers instead, choose the B, BS or BF variants (all available at bore 25, unlike bore 6). Thread is PT (Rc) on 1/8 ports as standard - swap to G or T in the code for BSPP or NPT plumbing. Allowable load and moment are published as tables and deflection curves, so route your load-case sizing through us rather than estimating.
Applications
Small-parts assembly press
The 25 mm bore supplies the higher thrust needed to seat press-fit components, while adjustable rubber stoppers give a repeatable, cushioned end position at bottom of stroke.
Assembly line stopper
Mounted beside a line, the slide acts as a precise stopper or pusher; the rigid cross-roller guide holds the part square as it is stopped over the 150 mm travel.
Long-travel pick-and-place
Carry a gripper or vacuum cup across the full 150 mm stroke between pick and place points - the symmetrical, low-deflection table keeps the payload path straight.
FAQ
What does the A at the end of HLSL25X150SA change?
The A is the adjuster code, available only on the HLS and HLSL series: it fits adjustable rubber stoppers at both ends of the stroke so you can tune the end position and soften impact. Alternatives are B/BS/BF for shock absorbers (offered from bore 8 up) or no code for the basic bumper-cushioned version.
What pressure and speed limits apply to this slide table?
Bore 25 models operate at 0.15-0.7 MPa (22-100 psi), with 0.7 MPa as the absolute maximum working pressure and 1.2 MPa proof pressure. Keep the table speed between 50 and 500 mm/s and use meter-out flow control for stable motion. Medium is air filtered to 40 um, and the ambient range is -20 to 70 C.