Airtac LRM Miniature Linear Guide LRM12N2X195S10CHT
The AirTAC Airtac LRM Miniature Linear Guide LRM12N2X195S10CHT is a miniature linear guide on a 12 mm stainless-steel rail with recirculating-ball carriages. It is the small end of the range, for light-duty precision positioning in a tight envelope — compact stages, small pick-and-place heads and inspection fixtures.
- SeriesLRM
- Supplied asComplete guide set
- SizeLRM12
- Rail width12 mm
- Carriage lengthStandard carriage
- Carriages2
- Rail length195 mm
- AccuracyH — high grade
- PreloadC — medium preload
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac LRM Miniature Linear Guide LRM12N2X195S10CHT
LRM12N2X195S10CHT is the bottom-mount version of the medium-preload twin-carriage 12 mm set: a 195 mm stainless-steel rail bolted through its base, two standard carriages on board, preload C and accuracy H. Choose it when the carriage top must present a flush, unobstructed deck to whatever it carries.
LRM12 is by far the deepest-stocked size in this range - roughly nine in ten of our stocked LRM sets - so this configuration typically ships without a wait. The 80 C ambient ceiling (100 C momentary) is worth checking early if the guide runs near a heater, lamp or curing oven; it is the one environmental figure the catalogue publishes. Recirculating balls are graded ISO 3290 G10, a grade that applies to the balls alone, not the assembly. Ball retention helps during handling, but a carriage fitted at an angle or swapped quickly can still lose balls - a dummy rail makes field changes safer. Because LRM carries no published load or moment ratings, we confirm capacity for this exact SKU before ordering; include it in your RFQ.
Airtac LRM Miniature Linear Guide LRM12N2X195S10CHT Technical Specifications
| Model | Airtac LRM Miniature Linear Guide LRM12N2X195S10CHT |
|---|---|
| Series | LRM Series Miniature Linear Guide |
| Supplied as | Complete guide set |
| Construction | Recirculating ball, stainless-steel rail, common-rail design |
| Size code | LRM12 |
| Rail width | 12 mm |
| Carriage length | Standard carriage |
| Carriages supplied | 2 |
| Rail length | 195 mm (spliced sections) |
| Load & moment ratings | Not published for this series — ask us to confirm for your model |
|---|---|
| Accuracy grade | H — high grade |
| Preload grade | C — medium preload |
| Mounting screws | M2 or M3 rail screws depending on size |
| Lubrication | Pre-filled with Kyodo Yushi PS No. 2; top up through the rear lubrication hole |
| Ambient temperature | Up to 80 °C ambient, 100 °C transient peak |
| Interchangeability | LRM carriages fit LRM rails of the same model |
Specifications follow the official AirTAC LRM catalogue. The catalogue does not publish load or moment ratings, running parallelism, speed limits, or carriage base material for LRM. We will not quote a figure we cannot source — ask us and we will confirm it for your model.
Model Code: Airtac LRM Miniature Linear Guide LRM12N2X195S10CHT
| LRM | LRM Series Miniature Linear Guide. |
|---|---|
| 12 | Size code. |
| N | Standard carriage. |
| 2X195 | 2 carriages on a 195 mm rail. |
| S… | End-hole offset from the rail end, in mm. |
| C | C — medium preload — higher preload raises rigidity and tightens how flat the mounting surface must be. |
| H | H — high grade. |
What Is In The Box
| This order | Complete guide set |
|---|---|
| Rail | Yes, 195 mm |
| Carriage | Yes, 2 |
Rail and carriage(s) supplied together, matched as a set. If you are not sure which form you need, send us the machine or the original part number and we will confirm it before you order.
Where the Airtac LRM Miniature Linear Guide LRM12N2X195S10CHT Is Used
Conveyor camera tracking head
A small inspection camera riding beside a mini conveyor, bottom-mounted so the lens side of the deck stays clear of passing product.
Connector crimp feed slide
Advancing wire harnesses under a benchtop crimper, with the twin-carriage layout resisting tipping along the 195 mm travel.
3D printer gantry retrofit
Upgrading a compact printer axis to recirculating-ball travel; wipe off the rust-preventive oil and apply fresh lubricant before first use.
Is the Airtac LRM Miniature Linear Guide LRM12N2X195S10CHT the Right Guide?
Sizing guidance: when the load is substantial or sits on an overhang, move to LSH - its published per-carriage dynamic, static and moment ratings let you calculate margins, something LRM cannot offer. LGC fits short, stiff, crossed-roller duties. For this SKU, confirm each point: complete set with rail, 12 mm rail width, standard block length, two carriages on a 195 mm rail, preload C (the rigid choice - make sure the ground or finish-milled seat can hold its tolerance), accuracy H, bottom-mount direction, and a load rating confirmed with us, since none is published for LRM. On long runs the rail can be spliced; spliced sets are accuracy H only and the joint marks and serial pairs must be matched during assembly.
Quick checklist
- ✓ Complete set, carriage only, or rail only?
- ✓ Load and moment confirmed with us
- ✓ Travel length and mounting space
- ✓ Accuracy grade and preload
- ✓ Mounting surface ground or finish-milled
- ✓ Pairing code, if replacing a part
Installation & Maintenance Notes
- check Mounting surface must be ground or finish-milled.
- check Torque the rail screws per the recommended figures, in sequence.
- check Keep the mounting corner radius inside the stated R maximum.
- check Do not angle the carriage onto the rail; balls can drop out.
- check Drive the supplied bolt caps into the mounting holes.
- check Re-grease every 100 km of travel or every 3–6 months.
- check Installation by qualified personnel per AirTAC docs.
Airtac LRM Miniature Linear Guide LRM12N2X195S10CHT FAQ
Yes: 12 mm rail width, 195 mm rail length, two standard carriages, preload C (medium), accuracy H (high), bottom-mount fixing, stainless-steel rail, ISO 3290 G10 balls. Screws: M2 torque 58.8 N.cm into steel, 39.2 into cast iron, 29.4 into aluminium; M3 at 196, 127 and 98 N.cm. Ambient must stay under 80 C, peaks to 100 C. Re-grease every 100 km of travel or every 3 to 6 months. What the catalogue does not publish for LRM: load ratings, moment ratings, running parallelism and speed limits - we confirm those per model before you order.
A complete set: one 195 mm bottom-mount stainless-steel rail with both standard carriages fitted and pre-greased with Kyodo Yushi PS No. 2. Carriages are not sold loose with this SKU. If you want a spare carriage later, that is a separate carriage-only part carrying a pairing code that must match its rail - and our carriage-only stock is very thin, so most replacements are a special order. When handling spares, remember balls can still drop if the carriage is tilted onto the rail or swapped hastily; a dummy rail helps.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac LRM Miniature Linear Guide LRM12N2X195S10CHT
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours. We can also confirm the load and moment rating for this model.