Airtac MAC Stainless Steel Mini Air Cylinder MAC25X600SCM
The AirTAC Airtac MAC Stainless Steel Mini Air Cylinder MAC25X600SCM is a genuine double acting + cushion standard round-body mini air cylinder with a Ø25mm bore and 600mm stroke, 1/8" air ports and a stainless-steel barrel with a hard-chrome-plated rod for reliable, mildly corrosion-resistant service. A variable air cushion at both ends lets you tune end-of-stroke deceleration on site.
- BoreØ25 mm
- Stroke600 mm
- Port size1/8"
- Acting typeDouble acting + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
About the Airtac MAC Stainless Steel Mini Air Cylinder MAC25X600SCM
Pick the round-ended CM cover when the rod should drive through a knuckle: this 600 mm MAC25X600SCM gives 245.3 N push and 206.1 N pull at 0.5 MPa, climbing to 343.4 N and 288.5 N on 0.7 MPa. Theoretical ceiling for the bore is 50 kgf.
Made to order because standard 25 mm strokes stop at 500 mm, it still ships with the magnet in the piston - CMSG / DMSG / EMSG switches read position anywhere along the barrel. The cushion needles at both ends dial out end-of-stroke bang; open them fully on commissioning, then close until the landing is clean. Budget about 147 N of honest push at 0.5 MPa for the mechanism, not the raw rating.
Airtac MAC Stainless Steel Mini Air Cylinder MAC25X600SCM Technical Specifications
| Model | Airtac MAC Stainless Steel Mini Air Cylinder MAC25X600SCM |
|---|---|
| Series | MAC mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 600 mm |
| Acting type | Double acting + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MA-series datasheet. Barrel: stainless-steel tube (round-body, riveted rolling-packed construction); piston rod: carbon steel with 20µm hard-chrome plating; covers: aluminium alloy. Thread options: PT (blank) / G / NPT. Every MA-series cylinder ships with a built-in magnet for CMSG / DMSG / EMSG position sensors.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MAC Stainless Steel Mini Air Cylinder MAC25X600SCM
| MAC | Standard round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 25 | Bore size in mm. |
| ×600 | Stroke length in mm. |
| -S | Built-in magnet for CMSG / DMSG / EMSG sensors (standard on MA series). |
| CA / U / CM | Back-cover type: CA pivot, U flat-end, CM round-end. |
MA-family variants: MA / MAC (double acting ±cushion), MSA / MTA (single acting push / pull), MAD / MACD (double rod ±cushion), MAJ / MACJ (adjustable stroke ±cushion), MAR (cushioned with integrated F/U mount). Mounting accessories: FA flange, LB foot, SDB pivot; plus I and Y knuckles. Thread PT (blank) / G / NPT.
Where the Airtac MAC Stainless Steel Mini Air Cylinder MAC25X600SCM Is Used
Chute tilt gate
Rocks a discharge chute open on a Y knuckle so granulate dumps cleanly into a weighing hopper below.
Lid lifter
Raises a polycarbonate cover on a small mixing vessel against its own weight before operator access.
Turntable stop
Drops a pivoting stop pin into the path of an indexing rotary table to arrest each station.
Is the Airtac MAC Stainless Steel Mini Air Cylinder MAC25X600SCM the Right Cylinder?
A 20 mm bore manages only 157.0 N at 0.5 MPa and the 32 mm bore offers 402.2 N, so pick 25 mm only if your linkage needs the middle band around 245.3 N. Because 600 mm is beyond the 500 mm standard limit, expect a made-to-order build. At this length every bit of misalignment multiplies - run the rod through a Y or I knuckle and let a machine guideway take the lateral forces.
If the mechanism must hold a gate open with no air, remember the rod settles under gravity once pressure goes; a rod lock variant or an external latch is the answer. Ports are 1/8" and the rod carries an M10x1.25 male thread.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) is standard for sensors
- ✓ Back cover (CA/U/CM) & mount (FA/LB/SDB)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check On first run, back off the cushion screws and release gradually.
- check Installation by qualified personnel per AirTAC docs.
Airtac MAC Stainless Steel Mini Air Cylinder MAC25X600SCM FAQ
Push 245.3 N and pull 206.1 N at 0.5 MPa; push 343.4 N and pull 288.5 N at 0.7 MPa; theoretical maximum 50 kgf. The rod measures 10 mm with M10x1.25 thread, both ports are 1/8", and operating pressure runs 0.15-1.0 MPa (22-145 psi).
Any of the CMSG, DMSG or EMSG series - the magnet comes fitted as standard, not as an option. Clip a switch anywhere along the 600 mm stainless barrel for mid-stroke or end detection. Air is filtered to 40 um and the fluid temperature window is -20 to +70 C.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MAC Stainless Steel Mini Air Cylinder MAC25X600SCM
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.