Airtac MAC Stainless Steel Mini Air Cylinder MAC32X200SCA
The AirTAC Airtac MAC Stainless Steel Mini Air Cylinder MAC32X200SCA is a genuine double acting + cushion standard round-body mini air cylinder with a Ø32mm bore and 200mm stroke, 1/8" air ports and a stainless-steel barrel with a hard-chrome-plated rod for reliable, mildly corrosion-resistant service. A variable air cushion at both ends lets you tune end-of-stroke deceleration on site.
- BoreØ32 mm
- Stroke200 mm
- Port size1/8"
- Acting typeDouble acting + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
About the Airtac MAC Stainless Steel Mini Air Cylinder MAC32X200SCA
With 200 mm of travel and a pivot-ready CA back cover, this 32 mm MAC cylinder handles longer slides and swinging linkages alike. Double acting throughout, it pushes 402 N and pulls 346 N at 0.5 MPa, and the variable air cushion at each end lets a 200 mm move finish quietly even at 800 mm/s.
Supply air from 0.15-1.0 MPa (22-145 psi); proof pressure is 1.5 MPa (215 psi). The rolling-packed stainless barrel and hard-chrome 12 mm rod resist corrosion in wet or outdoor spots where painted mini cylinders peel. Rated lift works out to 41 kgf at 0.5 MPa - halve that and you can hoist about 20 kg with margin to spare. CMSG, DMSG or EMSG switches clip straight on since the magnet ships as standard equipment.
Airtac MAC Stainless Steel Mini Air Cylinder MAC32X200SCA Technical Specifications
| Model | Airtac MAC Stainless Steel Mini Air Cylinder MAC32X200SCA |
|---|---|
| Series | MAC mini cylinder |
| Bore size | Ø32 mm |
| Stroke | 200 mm |
| Acting type | Double acting + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MA-series datasheet. Barrel: stainless-steel tube (round-body, riveted rolling-packed construction); piston rod: carbon steel with 20µm hard-chrome plating; covers: aluminium alloy. Thread options: PT (blank) / G / NPT. Every MA-series cylinder ships with a built-in magnet for CMSG / DMSG / EMSG position sensors.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | 484 N |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MAC Stainless Steel Mini Air Cylinder MAC32X200SCA
| MAC | Standard round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 32 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -S | Built-in magnet for CMSG / DMSG / EMSG sensors (standard on MA series). |
| CA / U / CM | Back-cover type: CA pivot, U flat-end, CM round-end. |
MA-family variants: MA / MAC (double acting ±cushion), MSA / MTA (single acting push / pull), MAD / MACD (double rod ±cushion), MAJ / MACJ (adjustable stroke ±cushion), MAR (cushioned with integrated F/U mount). Mounting accessories: FA flange, LB foot, SDB pivot; plus I and Y knuckles. Thread PT (blank) / G / NPT.
Where the Airtac MAC Stainless Steel Mini Air Cylinder MAC32X200SCA Is Used
Case packer layer push
The rod squares carton layers on a palletizer infeed across 200 mm of travel; 402 N at 0.5 MPa moves full layers without stalling.
Battery stillage latch
In a charging bay, the CA pivot retracts a spring-loaded latch arm on stillage racks; the cushioned ends prevent the arm slamming at cycle end.
Oven door slide actuator
A 200 mm pull opens a bakery deck-oven door via a bell-crank; the stainless body handles the steam-laden ambient without paint failure.
Is the Airtac MAC Stainless Steel Mini Air Cylinder MAC32X200SCA the Right Cylinder?
For heavier duty move to the 40 mm bore and its 628 N push at 0.5 MPa; for lighter cycles the 25 mm bore at 245 N saves air. A 200 mm stroke amplifies side load, so carry the payload on linear rails instead of cantilevering it off the rod. The cylinder keeps no position once air is dumped - a rod lock or pilot check valve is the answer where the slide must stay put. The CA pivot cover pairs with clevis mounts, and FA flange or LB foot brackets cover fixed installations.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) is standard for sensors
- ✓ Back cover (CA/U/CM) & mount (FA/LB/SDB)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check On first run, back off the cushion screws and release gradually.
- check Installation by qualified personnel per AirTAC docs.
Airtac MAC Stainless Steel Mini Air Cylinder MAC32X200SCA FAQ
Push 402 N and pull 346 N at 0.5 MPa; push 563 N and pull 484 N at 0.7 MPa; theoretical peak 82 kgf at 1.0 MPa (145 psi). Air port is 1/8", rod 12 mm with M10x1.25 thread, and the 200 mm stroke sits within the 500 mm standard range.
The CA pivot back cover is built in, while FA flange, LB foot and SDB pivot brackets plus I and Y rod knuckles bolt on when the layout needs them. Every unit also carries the standard magnet, so CMSG, DMSG and EMSG position switches mount without modification.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MAC Stainless Steel Mini Air Cylinder MAC32X200SCA
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.