Airtac MAC Stainless Steel Mini Air Cylinder MAC32X600SCMH
The AirTAC Airtac MAC Stainless Steel Mini Air Cylinder MAC32X600SCMH is a genuine double acting + cushion standard round-body mini air cylinder with a Ø32mm bore and 600mm stroke, 1/8" air ports and a stainless-steel barrel with a hard-chrome-plated rod for reliable, mildly corrosion-resistant service. A variable air cushion at both ends lets you tune end-of-stroke deceleration on site.
- BoreØ32 mm
- Stroke600 mm
- Port size1/8"
- Acting typeDouble acting + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
About the Airtac MAC Stainless Steel Mini Air Cylinder MAC32X600SCMH
Air reaches both sides of the piston, so this MAC extends and retracts under power - no spring return - and tops out at 402.2 N push and 345.6 N pull at 0.5 MPa. Derate to roughly 241 N for the working stroke and you get consistent cycle times plus long seal life; at full 1.0 MPa the bore reaches a theoretical 82 kgf.
The stainless round barrel shrugs off coolants and outdoor condensation, and the hard-chrome 12 mm rod resists scoring over long travel. Both ends carry a variable air cushion: crack the needle screws open on first run, then close them gradually to absorb shock. The CM round-end cover suits fixed face mounting, and the 600 mm length is built to order. The trailing H in the code does not appear in the standard suffix chart, so confirm its exact option from the datasheet before ordering.
Airtac MAC Stainless Steel Mini Air Cylinder MAC32X600SCMH Technical Specifications
| Model | Airtac MAC Stainless Steel Mini Air Cylinder MAC32X600SCMH |
|---|---|
| Series | MAC mini cylinder |
| Bore size | Ø32 mm |
| Stroke | 600 mm |
| Acting type | Double acting + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MA-series datasheet. Barrel: stainless-steel tube (round-body, riveted rolling-packed construction); piston rod: carbon steel with 20µm hard-chrome plating; covers: aluminium alloy. Thread options: PT (blank) / G / NPT. Every MA-series cylinder ships with a built-in magnet for CMSG / DMSG / EMSG position sensors.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | 484 N |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MAC Stainless Steel Mini Air Cylinder MAC32X600SCMH
| MAC | Standard round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 32 | Bore size in mm. |
| ×600 | Stroke length in mm. |
| -S | Built-in magnet for CMSG / DMSG / EMSG sensors (standard on MA series). |
| CA / U / CM | Back-cover type: CA pivot, U flat-end, CM round-end. |
MA-family variants: MA / MAC (double acting ±cushion), MSA / MTA (single acting push / pull), MAD / MACD (double rod ±cushion), MAJ / MACJ (adjustable stroke ±cushion), MAR (cushioned with integrated F/U mount). Mounting accessories: FA flange, LB foot, SDB pivot; plus I and Y knuckles. Thread PT (blank) / G / NPT.
Where the Airtac MAC Stainless Steel Mini Air Cylinder MAC32X600SCMH Is Used
Kiln Damper Arm
Opens a long damper arm on a heat-treatment furnace, where the stainless tube tolerates warm, humid air near the oven.
Case Elevator Gate
Drops the gate on a vertical case elevator between floors, lifting about 20 kg against gravity with margin to spare.
Boat-Slip Stopper
Positions a stop pin on a boat-slip guide rail, where the chrome-plated rod resists the salt-humid marine air.
Is the Airtac MAC Stainless Steel Mini Air Cylinder MAC32X600SCMH the Right Cylinder?
At 245.3 N of push, bore 25 is the step down; bore 40 with 628.3 N is the step up from this 32 mm bore. A centred valve or a loss of air lets the piston drift, so specify a rod lock or pilot check valve for held positions. The CM round-end back cover suits fixed bolt-through mounting; add FA flange or LB foot hardware as the frame demands. Because 600 mm of rod is long for a mini cylinder, keep the load carried in external linear bearings and avoid side thrust on the rod. Verify the meaning of the H suffix from the datasheet before you commit.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) is standard for sensors
- ✓ Back cover (CA/U/CM) & mount (FA/LB/SDB)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check On first run, back off the cushion screws and release gradually.
- check Installation by qualified personnel per AirTAC docs.
Airtac MAC Stainless Steel Mini Air Cylinder MAC32X600SCMH FAQ
At 0.5 MPa: 402.2 N push, 345.6 N pull. At 0.7 MPa: 563.0 N push, 483.8 N pull. Theoretical maximum 82 kgf at 1.0 MPa. Operating window 0.15-1.0 MPa (22-145 psi), speed 30-800 mm/s.
The piston magnet is fitted as standard, so CMSG / DMSG / EMSG switches clip on without a special-order piston. Speed spans 30-800 mm/s, so the 600 mm travel takes roughly 0.75 s at full speed. Bleed the variable cushion needle screws open on first run, then close them gradually to settle the end stops.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MAC Stainless Steel Mini Air Cylinder MAC32X600SCMH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.