Airtac MAC Stainless Steel Mini Air Cylinder MAC63X10SCM
The AirTAC Airtac MAC Stainless Steel Mini Air Cylinder MAC63X10SCM is a genuine double acting + cushion standard round-body mini air cylinder with a Ø63mm bore and 10mm stroke, 1/4" air ports and a stainless-steel barrel with a hard-chrome-plated rod for reliable, mildly corrosion-resistant service. A variable air cushion at both ends lets you tune end-of-stroke deceleration on site.
- BoreØ63 mm
- Stroke10 mm
- Port size1/4"
- Acting typeDouble acting + cushion
- Rod threadM14×1.5
- CushionVariable air cushion, both ends
About the Airtac MAC Stainless Steel Mini Air Cylinder MAC63X10SCM
Squeezing the largest cushioned mini bore into a 10 mm stroke, the MAC63X10SCM is a compact punch for clamping and short-jog moves on PT 1/4" air. It is double acting - air extends and retracts the rod - delivering 1557.9 N of push and 1457.4 N of pull at 0.5 MPa and up to 2181.0 N at 0.7 MPa. Supply 0.15-1.0 MPa (22-145 psi) and speed 30-800 mm/s leave wide tuning room.
Build quality is the round riveted MA style: stainless barrel, aluminium covers and a 16 mm chrome-plated rod, which resists washdown chemicals and damp workshops better than coated steel minis. Variable cushions at both ends take the bang out of rapid clamping - open the needle screws fully at start-up and close them gradually until the stop is quiet. Lift maths from the 0.5 MPa rating comes to about 159 kg dead-vertical, dropping to near 79 kg when a 2:1 safety factor is applied. The rounded CM cover hangs on a mounting pin for linkage clamps, and the magnet is standard for CMSG, DMSG or EMSG switches.
Airtac MAC Stainless Steel Mini Air Cylinder MAC63X10SCM Technical Specifications
| Model | Airtac MAC Stainless Steel Mini Air Cylinder MAC63X10SCM |
|---|---|
| Series | MAC mini cylinder |
| Bore size | Ø63 mm |
| Stroke | 10 mm |
| Acting type | Double acting + cushion |
| Port size | 1/4" |
| Rod thread | M14×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MA-series datasheet. Barrel: stainless-steel tube (round-body, riveted rolling-packed construction); piston rod: carbon steel with 20µm hard-chrome plating; covers: aluminium alloy. Thread options: PT (blank) / G / NPT. Every MA-series cylinder ships with a built-in magnet for CMSG / DMSG / EMSG position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1458 N |
| 0.7 MPa | 2182 N | 2041 N |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MAC Stainless Steel Mini Air Cylinder MAC63X10SCM
| MAC | Standard round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 63 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| -S | Built-in magnet for CMSG / DMSG / EMSG sensors (standard on MA series). |
| CA / U / CM | Back-cover type: CA pivot, U flat-end, CM round-end. |
MA-family variants: MA / MAC (double acting ±cushion), MSA / MTA (single acting push / pull), MAD / MACD (double rod ±cushion), MAJ / MACJ (adjustable stroke ±cushion), MAR (cushioned with integrated F/U mount). Mounting accessories: FA flange, LB foot, SDB pivot; plus I and Y knuckles. Thread PT (blank) / G / NPT.
Where the Airtac MAC Stainless Steel Mini Air Cylinder MAC63X10SCM Is Used
Marking stamp actuator
Drives a date-code stamp onto extruded profiles with a firm 10 mm hit; the cushion kills recoil so characters print crisp on every cycle.
Tab press on an assembly cell
Bends locator tabs on battery tray fixtures; 1557.9 N at 0.5 MPa forms 1 mm steel tabs without dedicating a full press to the job.
Presence plunger with feedback
Confirms a large casting is seated in its machining fixture, with an EMSG switch reporting the clamped position straight back to the PLC.
Is the Airtac MAC Stainless Steel Mini Air Cylinder MAC63X10SCM the Right Cylinder?
For a lighter 10 mm clamp the 32 mm bore (402.2 N push at 0.5 MPa) costs less; for more than 2181.0 N at 0.7 MPa this series tops out, so consider twin cylinders or a larger bore family. The drift warning applies here too: with no air or a centred valve the rod is free to slide, so add a pilot check valve or rod lock where a clamped part must remain secured. Hang the CM eye on a pin, or pick FA flange, LB foot and SDB hardware for fixed frames; the built-in magnet already supports switch sensing.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) is standard for sensors
- ✓ Back cover (CA/U/CM) & mount (FA/LB/SDB)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check On first run, back off the cushion screws and release gradually.
- check Installation by qualified personnel per AirTAC docs.
Airtac MAC Stainless Steel Mini Air Cylinder MAC63X10SCM FAQ
At 0.5 MPa, push 1557.9 N and pull 1457.4 N; at 0.7 MPa, push 2181.0 N and pull 2040.3 N; theoretical maximum 317.7 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi) and speed is 30-800 mm/s.
The barrel is high-precision stainless steel with aluminium-alloy covers rolled on and a 16 mm carbon-steel rod hard-chrome plated to 20 um, a mix that shrugs off mild corrosion and routine washdown. Thread options are PT, G and NPT.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MAC Stainless Steel Mini Air Cylinder MAC63X10SCM
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.