This model is discontinued
AirTAC has phased out the MAL series. The drop-in replacement is MBL32X150-CM — same bore, stroke, output force, port and mounting, so it fits the same application. Simply order the MBL32X150-CM in place of this model. The MBL replacement upgrades to a riveted rolling-packed body and the current CMSG / DMSG / EMSG sensor switches (the MAL used CS1-M / DS1-M).
Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X150-CM
The AirTAC Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X150-CM is a double-acting aluminum-barrel mini round cylinder with a Ø32mm bore and 150mm stroke, G1/8 air ports and a fixed rubber bumper. This model is discontinued — the drop-in replacement is the MBL32X150-CM, which matches its bore, stroke, force and mounting.
- BoreØ32 mm
- Stroke150 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- StatusDiscontinued → MBL32X150-CM
About the Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X150-CM
The AirTAC MAL32X150-CM is a discontinued double-acting aluminum mini round cylinder with a 32mm bore and 150mm stroke. It delivers 402N of push force and 346N of pull force at 0.5MPa, peaking at 82kgf under 1.0MPa. The exact drop-in replacement is the MBL32X150-CM, which matches the original bore, stroke, output force, G1/8 port, and mounting footprint exactly.
This legacy CM round-end configuration uses a fixed rubber bumper rather than an adjustable air cushion. The original MAL body featured threaded front and back covers, whereas the modern MBL replacement uses a riveted rolling-packed body. Because this specific SKU lacks an -S magnet, it cannot support any position sensing.
To upgrade, order the MBL32X150-CM. If your application requires end-of-stroke deceleration, step up to the MBLC variant which adds an adjustable air cushion the MAL never had. The 150mm stroke on a 12mm rod is susceptible to bending under side loads, so utilize the CM round-end pivot for arcing motion or add an external guide.
Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X150-CM Technical Specifications
| Model | Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X150-CM |
|---|---|
| Series | MAL aluminum-barrel mini round cylinder (discontinued) |
| Replacement | MBL32X150-CM |
| Bore size | Ø32 mm |
| Stroke | 150 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.1 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed rubber bumper |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MAL datasheet (now discontinued). The MBL32X150-CM carries the same ratings. Confirm against the product label before installation. Thread options: PT / G / NPT.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
The MBL32X150-CM produces the same force from the same bore — a true drop-in on output. Actual usable force is lower than theoretical; size with a margin.
Model Code: Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X150-CM
| MAL | Aluminum-barrel mini round cylinder, double acting (discontinued). |
|---|---|
| 32 | Bore size in mm (20/25/32/40). |
| ×150 | Stroke length in mm. |
| S | Optional magnet for a CS1-M / DS1-M sensor (MBL uses CMSG/DMSG/EMSG). |
| CA / U / CM | Back cover: CA pivot, U flat-end or CM round-end. |
Replacement mapping: MAL → MBL, MSAL → MSBL, MTAL → MTBL, MALD → MBLD, MALJ → MBLJ.
Where the Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X150-CM Is Used
Packaging Flap Folder
Pushes cardboard flaps at 402N of force during 150mm travel on high-speed cartoners, utilizing the CM round-end to accommodate slight pivot misalignment.
PCB Test Handler
Drives a testing probe array over a 150mm stroke, relying on the self-lubricating front-cover bearing guide to maintain steady 30-800mm/s cycling without external lubrication.
Textile Beam Indexer
Shifts heavy yarn beams laterally, where the heterogeneous two-way grease-retaining piston seal maintains consistent 346N pull force despite dusty factory environments.
Replacing the Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X150-CM with MBL32X150-CM
To replace the MAL32X150-CM, order the drop-in MBL32X150-CM. Verify your 32mm bore, 150mm stroke, G1/8 port, PT tapered thread, and CM round-end back cover. Since this SKU has no -S magnet, it cannot accept a sensor; if you need position detection, order the MBL32X150S-CM and use the current CMSG, DMSG, or EMSG switches instead of the legacy CS1-M or DS1-M.
For sizing, stepping down to the 25mm bore yields 245N push at 0.5MPa, while stepping up to the 40mm bore provides 628N push at 0.5MPa. A plain MBL does not hold its load when air is lost, so add an external rod lock for vertical positioning. At 150mm of travel on a 12mm rod, use an external guide rail or pivot mount to prevent rod bending.
Upgrade checklist
- ✓ Order the MBL32X150-CM (same bore/stroke/force)
- ✓ Same G1/8 port and mounting accessories
- ✓ Sensor: swap CS1-M/DS1-M → CMSG/DMSG/EMSG
- ✓ Need a cushion? use MBLC (adjustable air cushion)
- ✓ Confirm back cover (CA / U) and thread (PT/NPT/G)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.1 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Front/rear covers are threaded — not intended for field disassembly.
- check Use the correct mounting accessory (LB / FA / SDB) and back cover (CA / U / CM).
- check For new builds, specify the MBL32X150-CM instead of this discontinued model.
Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X150-CM FAQ
Yes, the MAL32X150-CM is discontinued. The exact drop-in replacement is the MBL32X150-CM, which shares the same 32mm bore, 150mm stroke, 402N push force at 0.5MPa, G1/8 port, and CM round-end mounting. The modern MBL uses a riveted rolling-packed body instead of the original threaded covers.
At 0.5MPa it provides 402N push and 346N pull; at 0.7MPa it provides 563N push, with a maximum theoretical force of 82kgf at 1.0MPa. Because this specific SKU lacks an -S magnet, it cannot accept CS1-M or DS1-M position sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
Drop-in Upgrade
The MBL32X150-CM replaces this model 1:1.
Fast Dispatch
MBL replacements usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Recommended AirTAC MBL Replacements
Request a Quote (Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X150-CM → MBL32X150-CM)
Tell us the quantity and destination — we quote the drop-in MBL32X150-CM replacement with price, stock and lead time, usually within 7-8 hours.