This model is discontinued
AirTAC has phased out the MAL series. The drop-in replacement is MBL32X170CA — same bore, stroke, output force, port and mounting, so it fits the same application. Simply order the MBL32X170CA in place of this model. The MBL replacement upgrades to a riveted rolling-packed body and the current CMSG / DMSG / EMSG sensor switches (the MAL used CS1-M / DS1-M).
Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X170CA
The AirTAC Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X170CA is a double-acting aluminum-barrel mini round cylinder with a Ø32mm bore and 170mm stroke, G1/8 air ports and a fixed rubber bumper. This model is discontinued — the drop-in replacement is the MBL32X170CA, which matches its bore, stroke, force and mounting.
- BoreØ32 mm
- Stroke170 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- StatusDiscontinued → MBL32X170CA
About the Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X170CA
The AirTAC MAL32X170CA is a discontinued double-acting aluminum mini round cylinder with a 32 mm bore and 170 mm stroke. It delivers 402 N of push force and 346 N of pull force at 0.5 MPa. AirTAC replaced this legacy unit with the MBL32X170CA, a drop-in alternative that matches the exact bore, stroke, output force, G1/8 port, and CA pivot mounting for a seamless swap.
This SKU features a CA pivot back cover designed to swing on a pin, accommodating arcing loads rather than rigidly binding the assembly. Because this specific configuration lacks the -S magnet, it cannot accept a position sensor. Note that the original MAL uses threaded front and back covers, whereas the modern MBL replacement features a riveted rolling-packed body for equally robust performance.
Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X170CA Technical Specifications
| Model | Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X170CA |
|---|---|
| Series | MAL aluminum-barrel mini round cylinder (discontinued) |
| Replacement | MBL32X170CA |
| Bore size | Ø32 mm |
| Stroke | 170 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.1 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed rubber bumper |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MAL datasheet (now discontinued). The MBL32X170CA carries the same ratings. Confirm against the product label before installation. Thread options: PT / G / NPT.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
The MBL32X170CA produces the same force from the same bore — a true drop-in on output. Actual usable force is lower than theoretical; size with a margin.
Model Code: Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X170CA
| MAL | Aluminum-barrel mini round cylinder, double acting (discontinued). |
|---|---|
| 32 | Bore size in mm (20/25/32/40). |
| ×170 | Stroke length in mm. |
| S | Optional magnet for a CS1-M / DS1-M sensor (MBL uses CMSG/DMSG/EMSG). |
| CA / U / CM | Back cover: CA pivot, U flat-end or CM round-end. |
Replacement mapping: MAL → MBL, MSAL → MSBL, MTAL → MTBL, MALD → MBLD, MALJ → MBLJ.
Where the Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X170CA Is Used
Pouch Packaging Diverter
Swings a diverter arm on a packaging line to route sealed pouches at 402 N push force, utilizing the CA pivot bracket to handle the arcing motion of the arm without binding.
Textile Loom Tensioner
Actuates a yarn tensioning guide through a 170 mm stroke, where the self-lubricating front-cover bearing guide ensures smooth, low-friction movement in a lint-heavy environment.
Carton Flap Folder
Pushes corrugated carton flaps into position for tape sealing, with the fixed rubber bumper absorbing the repeated impact at the end of the 170 mm extension stroke.
Replacing the Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X170CA with MBL32X170CA
To replace the MAL32X170CA, order the MBL32X170CA. Verify your setup accepts the PT tapered port thread on the G1/8 port, the M10x1.25 rod-end thread, and the CA pivot clevis. Since this unit has no -S magnet, it cannot support a sensor; if you ever need position detection, you must upgrade to an MBL32X170CAS and switch from the old CS1-M / DS1-M switches to the current CMSG / DMSG / EMSG family.
For sizing flexibility, stepping down to a 25 mm bore yields 245 N push at 0.5 MPa, while stepping up to a 40 mm bore provides 628 N push. At 170 mm of stroke, the 12 mm rod is susceptible to bending if subjected to off-center loads; rely on the CA pivot to absorb alignment shifts or add an external guide. The fixed rubber bumper softens end-of-stroke impacts but does not lock the rod—if air pressure drops, the load will drift. For adjustable end-cushioning, look at the current MBLC line instead.
Upgrade checklist
- ✓ Order the MBL32X170CA (same bore/stroke/force)
- ✓ Same G1/8 port and mounting accessories
- ✓ Sensor: swap CS1-M/DS1-M → CMSG/DMSG/EMSG
- ✓ Need a cushion? use MBLC (adjustable air cushion)
- ✓ Confirm back cover (CA / U) and thread (PT/NPT/G)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.1 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Front/rear covers are threaded — not intended for field disassembly.
- check Use the correct mounting accessory (LB / FA / SDB) and back cover (CA / U / CM).
- check For new builds, specify the MBL32X170CA instead of this discontinued model.
Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X170CA FAQ
Yes, the MAL32X170CA is discontinued. The exact drop-in replacement is the MBL32X170CA, which offers the same 32 mm bore, 170 mm stroke, G1/8 port, and CA pivot mounting. The main difference is that the MBL uses a riveted rolling-packed body instead of the MAL's threaded covers.
The 32 mm bore cylinder uses a 12 mm carbon-steel rod with an M10x1.25 rod-end thread. At 0.5 MPa it provides 402 N push and 346 N pull force. At 0.7 MPa the push force is 563 N, and the maximum theoretical force is 82 kgf at 1.0 MPa.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
Drop-in Upgrade
The MBL32X170CA replaces this model 1:1.
Fast Dispatch
MBL replacements usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Recommended AirTAC MBL Replacements
Request a Quote (Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X170CA → MBL32X170CA)
Tell us the quantity and destination — we quote the drop-in MBL32X170CA replacement with price, stock and lead time, usually within 7-8 hours.