This model is discontinued
AirTAC has phased out the MAL series. The drop-in replacement is MBL32X240CA — same bore, stroke, output force, port and mounting, so it fits the same application. Simply order the MBL32X240CA in place of this model. The MBL replacement upgrades to a riveted rolling-packed body and the current CMSG / DMSG / EMSG sensor switches (the MAL used CS1-M / DS1-M).
Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X240CA
The AirTAC Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X240CA is a double-acting aluminum-barrel mini round cylinder with a Ø32mm bore and 240mm stroke, G1/8 air ports and a fixed rubber bumper. This model is discontinued — the drop-in replacement is the MBL32X240CA, which matches its bore, stroke, force and mounting.
- BoreØ32 mm
- Stroke240 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- StatusDiscontinued → MBL32X240CA
About the Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X240CA
The AirTAC MAL32X240CA is a discontinued double-acting aluminum mini round cylinder delivering 402 N of push force at 0.5 MPa. It features a 32 mm bore, a 240 mm stroke, and a CA pivot back cover. AirTAC replaced this legacy unit with the MBL32X240CA, a drop-in alternative retaining the exact same force, G1/8 port, and mounting interface.
This SKU lacks a built-in magnet, so it cannot accept a position sensor. Unlike the original MAL which uses threaded front and back covers, the modern MBL replacement features a riveted rolling-packed body for structural rigidity. The piston relies on a heterogeneous two-way seal that retains grease, while a self-lubricating bearing guide in the front cover supports the 12 mm carbon-steel rod plated with 20 µm hard chrome.
Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X240CA Technical Specifications
| Model | Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X240CA |
|---|---|
| Series | MAL aluminum-barrel mini round cylinder (discontinued) |
| Replacement | MBL32X240CA |
| Bore size | Ø32 mm |
| Stroke | 240 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.1 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed rubber bumper |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MAL datasheet (now discontinued). The MBL32X240CA carries the same ratings. Confirm against the product label before installation. Thread options: PT / G / NPT.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
The MBL32X240CA produces the same force from the same bore — a true drop-in on output. Actual usable force is lower than theoretical; size with a margin.
Model Code: Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X240CA
| MAL | Aluminum-barrel mini round cylinder, double acting (discontinued). |
|---|---|
| 32 | Bore size in mm (20/25/32/40). |
| ×240 | Stroke length in mm. |
| S | Optional magnet for a CS1-M / DS1-M sensor (MBL uses CMSG/DMSG/EMSG). |
| CA / U / CM | Back cover: CA pivot, U flat-end or CM round-end. |
Replacement mapping: MAL → MBL, MSAL → MSBL, MTAL → MTBL, MALD → MBLD, MALJ → MBLJ.
Where the Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X240CA Is Used
Pallet Diverters
Swings via the CA clevis to push 402 N lateral loads, routing flat packaging pallets along a 240 mm arc on a packaging line.
Textile Loom Tensioning
Extends 240 mm to position yarn guides, using the fixed rubber bumper to soften rapid stroke ends at high cycle rates.
Bin Sweep Gates
Pivots to open heavy discharge gates on bulk ingredient silos, relying on the 563 N push force at 0.7 MPa to overcome material resistance.
Replacing the Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X240CA with MBL32X240CA
To replace this discontinued cylinder, order the MBL32X240CA and verify your 12 mm rod-end thread (M10x1.25) and PT port connections match. Because this configuration uses a CA pivot back cover, ensure your clevis pin is intact to accommodate arcing loads. If you need end-of-stroke cushioning, note that the MAL uses a fixed rubber bumper; for an adjustable air cushion, you must step up to the current MBLC series.
At 240 mm of travel, side-load tolerance is low due to the 12 mm rod diameter, so align the pivot precisely to prevent rod bending. If you need to adjust force, stepping down to the 25 mm bore yields 245 N push at 0.5 MPa, while stepping up to the 40 mm bore provides 628 N. Remember that neither the MAL nor the MBL holds position unpowered—add an external rod lock if gravity loads are present.
Upgrade checklist
- ✓ Order the MBL32X240CA (same bore/stroke/force)
- ✓ Same G1/8 port and mounting accessories
- ✓ Sensor: swap CS1-M/DS1-M → CMSG/DMSG/EMSG
- ✓ Need a cushion? use MBLC (adjustable air cushion)
- ✓ Confirm back cover (CA / U) and thread (PT/NPT/G)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.1 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Front/rear covers are threaded — not intended for field disassembly.
- check Use the correct mounting accessory (LB / FA / SDB) and back cover (CA / U / CM).
- check For new builds, specify the MBL32X240CA instead of this discontinued model.
Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X240CA FAQ
Yes, the MAL32X240CA is discontinued. The exact drop-in replacement is the MBL32X240CA, which matches the 32 mm bore, 240 mm stroke, CA pivot mounting, and G1/8 port. The MBL body uses a riveted rolling-packed design instead of the original threaded covers.
At 0.5 MPa, it pushes with 402 N and pulls with 346 N. At 0.7 MPa, push increases to 563 N, with a theoretical maximum of 82 kgf at 1.0 MPa. Because this specific SKU lacks the -S magnet, it cannot accept CS1-M or DS1-M sensors for rod detection.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
Drop-in Upgrade
The MBL32X240CA replaces this model 1:1.
Fast Dispatch
MBL replacements usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Recommended AirTAC MBL Replacements
Request a Quote (Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X240CA → MBL32X240CA)
Tell us the quantity and destination — we quote the drop-in MBL32X240CA replacement with price, stock and lead time, usually within 7-8 hours.