This model is discontinued
AirTAC has phased out the MAL series. The drop-in replacement is MBL32X30U — same bore, stroke, output force, port and mounting, so it fits the same application. Simply order the MBL32X30U in place of this model. The MBL replacement upgrades to a riveted rolling-packed body and the current CMSG / DMSG / EMSG sensor switches (the MAL used CS1-M / DS1-M).
Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X30U
The AirTAC Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X30U is a double-acting aluminum-barrel mini round cylinder with a Ø32mm bore and 30mm stroke, G1/8 air ports and a fixed rubber bumper. This model is discontinued — the drop-in replacement is the MBL32X30U, which matches its bore, stroke, force and mounting.
- BoreØ32 mm
- Stroke30 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- StatusDiscontinued → MBL32X30U
About the Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X30U
The AirTAC MAL32X30U is a discontinued double-acting aluminum mini round cylinder with a 32mm bore and 30mm stroke. It delivers a push force of 402 N and pull force of 346 N at 0.5 MPa. AirTAC replaced this legacy unit with the MBL32X30U, a drop-in alternative retaining the exact same force, G1/8 port, and flat-end rear cover. The U suffix denotes a rigid flat-end back cover for straight-line mounting.
This non-magnet SKU cannot accept a position sensor, lacking the internal ring required for switches. Unlike the legacy MAL which uses threaded front and back covers, the modern MBL replacement features a riveted rolling-packed body. The original MAL relies on a fixed rubber bumper to soften stroke ends, whereas the current MBLC variant introduces an adjustable air cushion for heavier loads.
Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X30U Technical Specifications
| Model | Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X30U |
|---|---|
| Series | MAL aluminum-barrel mini round cylinder (discontinued) |
| Replacement | MBL32X30U |
| Bore size | Ø32 mm |
| Stroke | 30 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.1 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed rubber bumper |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MAL datasheet (now discontinued). The MBL32X30U carries the same ratings. Confirm against the product label before installation. Thread options: PT / G / NPT.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
The MBL32X30U produces the same force from the same bore — a true drop-in on output. Actual usable force is lower than theoretical; size with a margin.
Model Code: Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X30U
| MAL | Aluminum-barrel mini round cylinder, double acting (discontinued). |
|---|---|
| 32 | Bore size in mm (20/25/32/40). |
| ×30 | Stroke length in mm. |
| S | Optional magnet for a CS1-M / DS1-M sensor (MBL uses CMSG/DMSG/EMSG). |
| CA / U / CM | Back cover: CA pivot, U flat-end or CM round-end. |
Replacement mapping: MAL → MBL, MSAL → MSBL, MTAL → MTBL, MALD → MBLD, MALJ → MBLJ.
Where the Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X30U Is Used
PCB Router Ejector
Deploys a 30mm stroke to push singulated circuit boards out of a routing fixture using 402 N of push force at 0.5 MPa.
Connector Insertion Press
Drives a rigid straight-line 30mm stroke to seat ribbon cable headers into housings, relying on the flat-end U back cover for alignment.
Carton Flap Tucker
Cycles rapidly to fold minor corrugated flaps prior to case sealing, utilizing the compact 32mm aluminum body in tight packaging lanes.
Replacing the Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X30U with MBL32X30U
To replace the MAL32X30U, order the MBL32X30U. Verify your 32mm bore, 30mm stroke, PT tapered port thread, and the U flat-end back cover. Because this specific SKU lacks an S designation, it cannot support a sensor; if you require position detection, you must upgrade to an MBL32X30US and switch to the modern CMSG, DMSG, or EMSG switch family. The fixed rubber bumper is not a lock, so fit an external rod lock if you need to hold a load during air loss.
When sizing, verify if 402 N of push at 0.5 MPa is optimal. Stepping down to the 25mm bore drops thrust to 245 N, while moving up to the 40mm bore increases it to 628 N. If your application demands adjustable end-cushioning rather than the standard rubber bumper, specify the MBLC32 series.
Upgrade checklist
- ✓ Order the MBL32X30U (same bore/stroke/force)
- ✓ Same G1/8 port and mounting accessories
- ✓ Sensor: swap CS1-M/DS1-M → CMSG/DMSG/EMSG
- ✓ Need a cushion? use MBLC (adjustable air cushion)
- ✓ Confirm back cover (CA / U) and thread (PT/NPT/G)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.1 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Front/rear covers are threaded — not intended for field disassembly.
- check Use the correct mounting accessory (LB / FA / SDB) and back cover (CA / U / CM).
- check For new builds, specify the MBL32X30U instead of this discontinued model.
Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X30U FAQ
Yes, the MAL series is end-of-life. The exact drop-in replacement is the MBL32X30U. It matches the 32mm bore, 30mm stroke, 402 N push force, G1/8 port, and U flat-end back cover. The modern MBL uses a riveted body instead of threaded covers.
At 0.5 MPa it provides 402 N push and 346 N pull; at 0.7 MPa push is 563 N, with a maximum theoretical force of 82 kgf at 1.0 MPa. This SKU lacks a magnet, so it cannot accept CS1-M or DS1-M sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
Drop-in Upgrade
The MBL32X30U replaces this model 1:1.
Fast Dispatch
MBL replacements usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Recommended AirTAC MBL Replacements
Request a Quote (Airtac MAL32 Aluminum Alloy Mini Air Cylinder MAL32X30U → MBL32X30U)
Tell us the quantity and destination — we quote the drop-in MBL32X30U replacement with price, stock and lead time, usually within 7-8 hours.