Airtac MFC Cushioned Stainless Steel Mini Cylinder MFC32X110SU
The AirTAC Airtac MFC Cushioned Stainless Steel Mini Cylinder MFC32X110SU is a genuine double acting + cushion JIS-standard round-body mini air cylinder with a Ø32mm bore and 110mm stroke, 1/4" air ports and a SUS304 stainless-steel barrel for mildly corrosive environments. For the same bore and stroke it is shorter than an ISO 6432 cylinder, saving mounting space.
- BoreØ32 mm
- Stroke110 mm
- Port size1/4"
- Acting typeDouble acting + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
About the Airtac MFC Cushioned Stainless Steel Mini Cylinder MFC32X110SU
Delivering 402.2 N of push force at 0.5 MPa, this double-acting 32 mm bore mini cylinder is built for high-speed actuation where shock control matters. The variable air cushion at both ends lets you dial in the needle valve to smoothly decelerate the 110 mm stroke, absorbing end-of-travel impact and cutting noise. A JIS-standard round-body design with a SUS304 stainless barrel and riveted aluminium covers, it shrinks mounting length compared to an ISO 6432 cylinder of the same bore and stroke.
The built-in piston magnet (-S suffix) enables direct mounting of CMSG, DMSG or EMSG switches for position sensing. With a 1/4 inch air port and an M10x1.25 male rod thread, it provides a robust interface for mid-range loads. Based on the 0.5 MPa thrust, expect a safe working load around 241 N, or vertical lift capacity of about 20.5 kg with a 2:1 safety margin.
Airtac MFC Cushioned Stainless Steel Mini Cylinder MFC32X110SU Technical Specifications
| Model | Airtac MFC Cushioned Stainless Steel Mini Cylinder MFC32X110SU |
|---|---|
| Series | MFC JIS mini cylinder |
| Bore size | Ø32 mm |
| Stroke | 110 mm |
| Acting type | Double acting + cushion |
| Port size | 1/4" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MF/MFC (JIS-standard) datasheet. Barrel: SUS304 stainless steel; covers: aluminum alloy (round-body, riveted rolling-packed construction). Thread options: PT (blank) / G / NPT.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | 484 N |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MFC Cushioned Stainless Steel Mini Cylinder MFC32X110SU
| MFC | JIS-standard round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 32 | Bore size in mm. |
| ×110 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MF-family variants: MF / MFC (double acting ±cushion), MSF / MTF (single acting push / pull), MFD / MFCD (double rod ±cushion), MFJ / MFCJ (adjustable stroke ±cushion). Back covers CA / U / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MFC Cushioned Stainless Steel Mini Cylinder MFC32X110SU Is Used
Package Diverting
Pushes medium-weight cartons at high cycle rates on a sorting line, using the adjustable cushion to prevent slamming at the 110 mm stroke end.
Light Pressing
Applies steady 402.2 N clamping force for assembling small housings, where the SUS304 barrel resists minor shop floor splashes.
Vertical Lift Gates
Raises access flaps or lightweight machine guards, safely lifting loads up to 20.5 kg while the cushion softens the descent.
Is the Airtac MFC Cushioned Stainless Steel Mini Cylinder MFC32X110SU the Right Cylinder?
If 245.3 N from the MFC25 is insufficient, this 32 mm bore provides a solid step up; for heavier rigs requiring 628.3 N, step to the MFC40. The adjustable cushion is essential when cycling at high speeds or moving substantial mass, as it prevents harsh end-stop banging. Remember the cushion only decelerates near stroke end—it is not a lock. If you need to hold a vertical load during air loss, add an external rod lock or pilot check valve.
This U-flat rear cover variant suits direct flange mounting. The included magnet means the cylinder is immediately ready for reed or electronic sensors without further modification.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MFC Cushioned Stainless Steel Mini Cylinder MFC32X110SU FAQ
This double-acting cylinder has a 1/4 inch air port and an M10x1.25 male rod thread. It generates 402.2 N push and 345.6 N pull at 0.5 MPa, 563 N push and 483.8 N pull at 0.7 MPa, with a theoretical maximum force of 82 kgf at 1.0 MPa.
No, the variable air cushion only decelerates the piston near stroke end and acts purely as a shock absorber, never a brake. To prevent drift on air loss, install an external rod lock or pilot-operated check valve. The -S magnet allows CMSG/DMSG/EMSG sensors to confirm position.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MFC Cushioned Stainless Steel Mini Cylinder MFC32X110SU
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.