Airtac MG Stainless Steel Mini Air Cylinder MG32X300
The AirTAC Airtac MG Stainless Steel Mini Air Cylinder MG32X300 is a genuine double acting JIS-standard round-body mini air cylinder with a Ø32mm bore and 300mm stroke, 1/8" air ports and a SUS304 stainless-steel barrel with a hard-chrome-plated rod for reliable, mildly corrosion-resistant service.
- BoreØ32 mm
- Stroke300 mm
- Port size1/8"
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionFixed anti-impact bumper pads
About the Airtac MG Stainless Steel Mini Air Cylinder MG32X300
With a 32 mm bore and a long 300 mm stroke, this double acting MG mini cylinder delivers about 402.2 N of push at 0.5 MPa and 563 N at 0.7 MPa, on a JIS round-body design rolled from a SUS304 stainless barrel around riveted covers. The hard-chrome plated 12 mm rod resists wear and mild washdown, and the fixed anti-impact bumper pad at each end softens the stroke-end knock without adding the bulk of a cushioned body.
In practice, plan on roughly 241 N of usable work at 0.5 MPa (about 0.6 of the rated push), which means this bore lifts around 20 kg vertically with a 2:1 margin. The 300 mm travel suits longer reach tasks, and the JIS mounting footprint drops straight into standard mini-cylinder brackets and I or Y rod knuckles. Note that the rod is not held when air is lost, so an external lock or pilot check valve is needed for a suspended load.
Airtac MG Stainless Steel Mini Air Cylinder MG32X300 Technical Specifications
| Model | Airtac MG Stainless Steel Mini Air Cylinder MG32X300 |
|---|---|
| Series | MG JIS mini cylinder |
| Bore size | Ø32 mm |
| Stroke | 300 mm |
| Acting type | Double acting |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed anti-impact bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MG-series (JIS standard) datasheet. Barrel: SUS304 stainless steel (round-body, riveted construction); piston rod: carbon steel with 20µm hard-chrome plating. Thread options: PT (blank) / G / NPT.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | 484 N |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MG Stainless Steel Mini Air Cylinder MG32X300
| MG | JIS round-body mini cylinder (double-acting). |
|---|---|
| 32 | Bore size in mm. |
| ×300 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
| FA / LB / CB / SDB | Mounting: FA flange, LB foot, CB clevis, SDB pivot bracket (with CB). |
MG-family variants: MG / MGC (double acting ±cushion), MSG / MTG (single acting push / pull), MGD / MGCD (double rod ±cushion). Accessories: LB foot, FA flange, CB clevis, SDB pivot block, plus I and Y knuckles. Thread PT (blank) / G / NPT.
Where the Airtac MG Stainless Steel Mini Air Cylinder MG32X300 Is Used
Bottling line pusher
The 402.2 N push at 0.5 MPa easily nudges rows of 500 ml bottles off a conveyor lane, and the 300 mm stroke clears a wide transfer table in one move.
Small parts lift in assembly fixtures
With about 20 kg of vertical lift capacity at a 2:1 margin, this bore raises palletized connector trays between an indexing dial and an inspection camera.
Lab sample handling slide
The SUS304 stainless barrel and hard-chrome rod shrug off repeated wipe-downs in a wet sample-prep station, while the 300 mm travel slides a rack between wash and dry zones.
Is the Airtac MG Stainless Steel Mini Air Cylinder MG32X300 the Right Cylinder?
Compare by push force at 0.5 MPa: the 25 mm bore gives 245.3 N, this 32 mm bore gives 402.2 N, and the 40 mm bore reaches 628.3 N. If your load sits between 240 and 400 N of real demand, the 32 mm bore is the balanced pick; step down for lighter clamping, or step up when force margin matters more than size. At 300 mm stroke, watch side loads: keep them low and guide the load externally, because a long thin rod bends easily. Mounting options are LB foot, FA flange, CB clevis or SDB pivot, and this SKU carries no magnet, so position sensing with CMSG / DMSG / EMSG switches requires ordering the -S version.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Mounting (LB / FA / CB / SDB) & knuckle
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check On first run, back off the cushion/impact settings and release gradually.
- check Installation by qualified personnel per AirTAC docs.
Airtac MG Stainless Steel Mini Air Cylinder MG32X300 FAQ
At 0.5 MPa it pushes 402.2 N and pulls 345.6 N; at 0.7 MPa it pushes 563 N and pulls 483.8 N. The theoretical maximum is 82 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof pressure, and speed runs 30-800 mm/s.
Not as supplied. This MG32X300 has no magnet, so CMSG, DMSG or EMSG switches cannot detect the piston. Order the magnet version (MG32X300S) if you need end-of-stroke or mid-stroke sensing.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MG Stainless Steel Mini Air Cylinder MG32X300
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.