Airtac PB Pen-type Cylinder PB10X160SU
The AirTAC Airtac PB Pen-type Cylinder PB10X160SU is a double-acting pen-size (mini) air cylinder with a Ø10mm bore and 160mm stroke. Its slim round barrel and back cover are stainless steel, the M5×0.8 ports keep plumbing compact, and the fast, low-friction piston suits high-cycle small-part handling.
- BoreØ10 mm
- Stroke160 mm
- Port sizeM5×0.8
- Acting typeDouble acting
- Rod threadM8×1.0
- CushionElastic bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PB Pen-type Cylinder PB10X160SU
The AirTAC PB10X160SU is a double-acting JIS pen-size mini cylinder engineered for compact, high-frequency small-part motion. It delivers a theoretical push of 39.3 N and pull of 33 N at 0.5 MPa, driven through an M5x0.8 port. The slim SUS304 stainless barrel and screwed-in covers provide excellent durability in damp or mildly corrosive work areas while saving critical space on light end-of-arm tooling.
This 160 mm stroke variant includes a built-in piston magnet (S) for position sensing and a U-type back cover featuring a 90-degree perpendicular air inlet for flat plumbing. Because the rod is a slender 4 mm diameter, maintaining coaxial thrust is essential over this longer travel distance to prevent binding. The unit relies on a fixed TPU bumper at each end to decelerate the piston, which is not field-adjustable.
Airtac PB Pen-type Cylinder PB10X160SU Technical Specifications
| Model | Airtac PB Pen-type Cylinder PB10X160SU |
|---|---|
| Series | PB JIS pen-size mini cylinder |
| Bore size | Ø10 mm |
| Rod diameter | Ø4 mm |
| Stroke | 160 mm |
| Acting type | Double acting |
| Port size | M5×0.8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.2 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 800 mm/s |
| Cushion | Elastic bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC PB pen-size datasheet. Piston rod and barrel are stainless steel. Confirm bore, stroke and back-cover option against the product label before installation.
Theoretical Output Force (Ø10mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 39.3 N | 33.0 N |
| 0.7 MPa (max) | 55.0 N | 46.2 N |
Values are taken from the AirTAC PB thrust table. Because pull acts on the rod-side annular area, pull force is always lower than push. Actual usable force is reduced by friction — size with a margin.
Model Code: Airtac PB Pen-type Cylinder PB10X160SU
| PB | JIS pen-size double-acting mini-cylinder series. |
|---|---|
| 10 | Bore size in mm. |
| ×160 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| CB / U / R | Back cover: CB double clevis, U 90° side inlet, R axial inlet (bore-dependent). |
Mounting accessories: LB, FA, CJ. Related PB-family variants: PSB (single-acting push), PTB (single-acting pull), PBD (double rod), PBJ (adjustable stroke), PBR (front-mount).
Where the Airtac PB Pen-type Cylinder PB10X160SU Is Used
PCB Depaneling Router
Extends a 4 mm tooling pin to secure circuit boards during routing, utilizing the 160 mm travel to reach deep into the work envelope without consuming excessive vertical space.
Carton Flap Folder
Tucks minor flaps on small pharmaceutical cartons on a high-speed line, where the 39.3 N push force at 0.5 MPa is sufficient and the slim body fits between conveyor guides.
Pick-and-Place Ejector
Acts as a lightweight ejector on a robotic gripper, pushing delicate plastic components out of a mold cavity using a smooth 2 kg vertical lift capacity guided by an external linear bearing.
Is the Airtac PB Pen-type Cylinder PB10X160SU the Right Cylinder?
When sizing this actuator, stepping down to a 6 mm bore yields a 14.2 N push at 0.5 MPa, while stepping up to a 12 mm bore provides 56.5 N, allowing you to tune the payload precisely. For the PB10X160SU, plan for a safe working load of roughly 24 N (about 60 percent of the 0.5 MPa theoretical force) to account for seal friction. This equates to lifting approximately 2 kg vertically with a sane 2:1 safety margin. Confirm your ordering essentials: 10 mm bore, 160 mm stroke, M5x0.8 port, S magnet, and U back cover.
Note that a standard double-acting cylinder like this will drift and cannot hold a load if air pressure is lost or the valve is centered. The fixed bumpers only decelerate the stroke near the end caps and do not function as a locking brake. If your application requires fail-safe position holding, you must incorporate an external stop or a dedicated rod lock.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Slim pen body vs. a standard round cylinder
- ✓ Back cover: CB / U / R inlet direction
- ✓ Magnet (S) for sensors?
- ✓ Mounting: LB / FA / CJ or front thread
- ✓ Keep the load coaxial — avoid side load
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 0.7 MPa operating pressure.
- check Keep the load coaxial; avoid side load on the thin rod.
- check Do not dismantle the front or back cover.
- check Fit dust caps to ports during long-term storage.
- check Installation by qualified personnel per AirTAC docs.
Airtac PB Pen-type Cylinder PB10X160SU FAQ
At 0.5 MPa, the push force is 39.3 N and the pull force is 33 N. At the maximum operating pressure of 0.7 MPa, the push is 55 N and the pull is 46.2 N. The operating pressure range is 0.15-0.7 MPa, with a speed of 50-800 mm/s.
The U suffix denotes a 90-degree perpendicular side air inlet for flat plumbing in tight spaces. The S suffix means it has a built-in piston magnet compatible with AirTAC reed or electronic switches. It uses fixed TPU bumpers at both ends, which are not adjustable, so you may need external shock absorbers for heavy loads.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC PB Pen-Size Cylinders
Request a Quote for Airtac PB Pen-type Cylinder PB10X160SU
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.