Airtac PB Pen-type Cylinder PB10X180SU
The AirTAC Airtac PB Pen-type Cylinder PB10X180SU is a double-acting pen-size (mini) air cylinder with a Ø10mm bore and 180mm stroke. Its slim round barrel and back cover are stainless steel, the M5×0.8 ports keep plumbing compact, and the fast, low-friction piston suits high-cycle small-part handling.
- BoreØ10 mm
- Stroke180 mm
- Port sizeM5×0.8
- Acting typeDouble acting
- Rod threadM8×1.0
- CushionElastic bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PB Pen-type Cylinder PB10X180SU
The AirTAC PB10X180SU is a double-acting JIS pen-size mini cylinder engineered for compact, high-frequency small-part motion. It delivers 39.3 N of push force and 33 N of pull force at 0.5 MPa, utilizing a slim SUS304 stainless steel round barrel and a 4 mm piston rod to fit tight jigs and light end-of-arm tooling. This 10 mm bore model features an M5x0.8 air port and an M8x1.0 rod-end thread for straightforward load coupling.
Equipped with a built-in piston magnet (-S), it supports AirTAC reed or electronic switches for precise position detection. The U back cover provides a 90-degree side air inlet for flat plumbing in space-constrained installations. Because the stroke extends to 180 mm, the slender 4 mm rod requires an external guide or linear bearing to prevent side-load damage and maintain coaxial thrust.
Airtac PB Pen-type Cylinder PB10X180SU Technical Specifications
| Model | Airtac PB Pen-type Cylinder PB10X180SU |
|---|---|
| Series | PB JIS pen-size mini cylinder |
| Bore size | Ø10 mm |
| Rod diameter | Ø4 mm |
| Stroke | 180 mm |
| Acting type | Double acting |
| Port size | M5×0.8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.2 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 800 mm/s |
| Cushion | Elastic bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC PB pen-size datasheet. Piston rod and barrel are stainless steel. Confirm bore, stroke and back-cover option against the product label before installation.
Theoretical Output Force (Ø10mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 39.3 N | 33.0 N |
| 0.7 MPa (max) | 55.0 N | 46.2 N |
Values are taken from the AirTAC PB thrust table. Because pull acts on the rod-side annular area, pull force is always lower than push. Actual usable force is reduced by friction — size with a margin.
Model Code: Airtac PB Pen-type Cylinder PB10X180SU
| PB | JIS pen-size double-acting mini-cylinder series. |
|---|---|
| 10 | Bore size in mm. |
| ×180 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| CB / U / R | Back cover: CB double clevis, U 90° side inlet, R axial inlet (bore-dependent). |
Mounting accessories: LB, FA, CJ. Related PB-family variants: PSB (single-acting push), PTB (single-acting pull), PBD (double rod), PBJ (adjustable stroke), PBR (front-mount).
Where the Airtac PB Pen-type Cylinder PB10X180SU Is Used
PCB Edge-Guiding Arm
Pushes delicate circuit boards into test fixtures using the 24 N safe working load, while the SUS304 body resists flux fumes in selective soldering lines.
Thin-Film Diverter Gate
Cycles at 50-800 mm/s to deflect lightweight packaging films on a conveyor, with the U side inlet keeping the hose routing flat against the machine frame.
Lab Sample Ejector
Extends 180 mm to eject filled microplates from a centrifuge, requiring an external linear bearing to guide the 4 mm rod over the long stroke.
Is the Airtac PB Pen-type Cylinder PB10X180SU the Right Cylinder?
When sizing this 10 mm bore actuator, consider stepping down to the 6 mm bore for lighter loads (14.2 N push at 0.5 MPa) or up to the 12 mm bore for heavier tasks (56.5 N push at 0.5 MPa). For the PB10X180SU, plan for a safe working load of roughly 24 N at 0.5 MPa, accounting for seal friction and smooth travel, which translates to lifting about 2 kg vertically with a sane 2:1 margin.
A plain double-acting cylinder does not hold its position or load when air is lost or the valve is centred; the piston drifts, and the fixed TPU bumper only decelerates it near stroke end. For a fail-safe hold, an external stop or rod lock is required. Confirm your ordering essentials: 10 mm bore, 180 mm stroke, M5x0.8 port, S magnet, U 90-degree side inlet, and no mounting bracket.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Slim pen body vs. a standard round cylinder
- ✓ Back cover: CB / U / R inlet direction
- ✓ Magnet (S) for sensors?
- ✓ Mounting: LB / FA / CJ or front thread
- ✓ Keep the load coaxial — avoid side load
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 0.7 MPa operating pressure.
- check Keep the load coaxial; avoid side load on the thin rod.
- check Do not dismantle the front or back cover.
- check Fit dust caps to ports during long-term storage.
- check Installation by qualified personnel per AirTAC docs.
Airtac PB Pen-type Cylinder PB10X180SU FAQ
At 0.5 MPa, the push force is 39.3 N and the pull force is 33 N. At the maximum operating pressure of 0.7 MPa, the push force is 55 N and the pull force is 46.2 N. The operating pressure range is 0.15-0.7 MPa, the proof pressure is 1.2 MPa, and the speed range is 50-800 mm/s.
The -S code indicates a built-in piston magnet that works with AirTAC reed or electronic switches for position detection. For cushioning, it uses a fixed TPU bumper at each end that only decelerates the last few mm of travel; it is not adjustable, so at higher speeds with real tooling mass you should meter-out the exhaust or add an external shock absorber.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC PB Pen-Size Cylinders
Request a Quote for Airtac PB Pen-type Cylinder PB10X180SU
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.