Airtac PB Pen-type Cylinder PB10X50SU
The AirTAC Airtac PB Pen-type Cylinder PB10X50SU is a double-acting pen-size (mini) air cylinder with a Ø10mm bore and 50mm stroke. Its slim round barrel and back cover are stainless steel, the M5×0.8 ports keep plumbing compact, and the fast, low-friction piston suits high-cycle small-part handling.
- BoreØ10 mm
- Stroke50 mm
- Port sizeM5×0.8
- Acting typeDouble acting
- Rod threadM8×1.0
- CushionElastic bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PB Pen-type Cylinder PB10X50SU
The AirTAC PB10X50SU is a double-acting JIS pen-size mini cylinder engineered for compact, high-frequency motion. It delivers a theoretical push of 39.3 N and pull of 33 N at 0.5 MPa, driven through an M5x0.8 port. The slim SUS304 stainless steel barrel and 4 mm piston rod provide excellent durability in damp or mildly corrosive workspaces while keeping end-of-arm tooling exceptionally light.
This 50 mm stroke unit includes a built-in piston magnet (-S) for position sensing and a U-type back cover featuring a 90-degree side air inlet for flat plumbing along tight machine frames. Deceleration relies on fixed TPU bumpers at each end, which are not adjustable. For payloads moving at higher speeds, metering out the exhaust or adding an external shock absorber is recommended to prevent bottoming out.
Airtac PB Pen-type Cylinder PB10X50SU Technical Specifications
| Model | Airtac PB Pen-type Cylinder PB10X50SU |
|---|---|
| Series | PB JIS pen-size mini cylinder |
| Bore size | Ø10 mm |
| Rod diameter | Ø4 mm |
| Stroke | 50 mm |
| Acting type | Double acting |
| Port size | M5×0.8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.2 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 800 mm/s |
| Cushion | Elastic bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC PB pen-size datasheet. Piston rod and barrel are stainless steel. Confirm bore, stroke and back-cover option against the product label before installation.
Theoretical Output Force (Ø10mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 39.3 N | 33.0 N |
| 0.7 MPa (max) | 55.0 N | 46.2 N |
Values are taken from the AirTAC PB thrust table. Because pull acts on the rod-side annular area, pull force is always lower than push. Actual usable force is reduced by friction — size with a margin.
Model Code: Airtac PB Pen-type Cylinder PB10X50SU
| PB | JIS pen-size double-acting mini-cylinder series. |
|---|---|
| 10 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| CB / U / R | Back cover: CB double clevis, U 90° side inlet, R axial inlet (bore-dependent). |
Mounting accessories: LB, FA, CJ. Related PB-family variants: PSB (single-acting push), PTB (single-acting pull), PBD (double rod), PBJ (adjustable stroke), PBR (front-mount).
Where the Airtac PB Pen-type Cylinder PB10X50SU Is Used
PCB Depaneling Jig
Actuates a small cutting blade or clamping finger in a tight electronics assembly fixture, utilizing the 90-degree side inlet to keep plumbing flush against the machine frame.
Blister Pack Sorting
Pushes lightweight plastic blister packs into a diverting chute at high frequency, benefiting from the SUS304 stainless build in washdown-adjacent packaging areas.
Lab Sample Dispenser
Drives a micro-pipette or small valve block for liquid handling, where the built-in magnet confirms stroke end-position via a reed or electronic switch.
Is the Airtac PB Pen-type Cylinder PB10X50SU the Right Cylinder?
When sizing this actuator, plan for a safe working load of about 24 N, which accounts for roughly 60% of the 39.3 N theoretical push at 0.5 MPa to overcome seal friction and ensure smooth travel. In vertical lift scenarios, this equates to lifting about 2 kg with a sane 2:1 safety margin. If you need slightly less force, the Ø6 bore provides 14.2 N of push at 0.5 MPa; stepping up to the Ø12 bore yields 56.5 N. Keep in mind the 4 mm rod is built for coaxial thrust, so over this 50 mm stroke you should add an external linear bearing if any off-axis load is present. A plain PB cylinder does not hold its position if air pressure drops or the valve is centered, so an external rod lock is required for fail-safe holding. To order, confirm the 10 mm bore, 50 mm stroke, M5x0.8 port, S magnet, and U back cover.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Slim pen body vs. a standard round cylinder
- ✓ Back cover: CB / U / R inlet direction
- ✓ Magnet (S) for sensors?
- ✓ Mounting: LB / FA / CJ or front thread
- ✓ Keep the load coaxial — avoid side load
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 0.7 MPa operating pressure.
- check Keep the load coaxial; avoid side load on the thin rod.
- check Do not dismantle the front or back cover.
- check Fit dust caps to ports during long-term storage.
- check Installation by qualified personnel per AirTAC docs.
Airtac PB Pen-type Cylinder PB10X50SU FAQ
At 0.5 MPa, the push force is 39.3 N and the pull force is 33 N. At the maximum operating pressure of 0.7 MPa, the push is 55 N and the pull is 46.2 N. The operating pressure range is 0.15-0.7 MPa, with a speed range of 50-800 mm/s and a proof pressure of 1.2 MPa.
No, the piston will drift if air is lost or the valve is centered. The fixed TPU bumper only decelerates the rod near the stroke end and does not act as a lock. For vertical applications requiring fail-safe holding, you must add an external stop or rod lock.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC PB Pen-Size Cylinders
Request a Quote for Airtac PB Pen-type Cylinder PB10X50SU
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.