Airtac SAID100 Double Rod Cylinder SAID100X145S
The AirTAC Airtac SAID100 Double Rod Cylinder SAID100X145S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø100mm bore and 145mm stroke, G1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ100 mm
- Stroke145 mm
- Port sizeG1/2
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SAID100 Double Rod Cylinder SAID100X145S
The AirTAC SAID100X145-S is a double-acting, double-rod ISO 15552 profile cylinder equipped with a magnet for position sensing. A single piston drives a carbon steel rod out of both end covers, yielding identical extend and retract forces. You get 3681 N of thrust and pull each way at 0.5 MPa, rising to 6626 N at 0.9 MPa.
Because the rod exits the rear cover, you can mount a position flag or cam on the opposite end to trigger CMSE reed or DMSE electronic sensors. The extruded aluminum barrel includes sensor grooves on both sides, and the adjustable air cushions at both ends absorb kinetic energy near stroke end.
Airtac SAID100 Double Rod Cylinder SAID100X145S Technical Specifications
| Model | Airtac SAID100 Double Rod Cylinder SAID100X145S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 145 mm |
| Acting type | Double acting |
| Port size | G1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SAID100 Double Rod Cylinder SAID100X145S
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×145 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SAID100 Double Rod Cylinder SAID100X145S Is Used
Symmetric Transfer
Drives a workpiece back and forth with equal 3681 N force in both directions, ensuring consistent cycle timing for automated transfer lines.
Anti-Rotation Slides
Uses the twin-rod geometry to guide loads and prevent rotation without external guide rails, ideal for vertical lifting slides.
Rear-Tool Actuation
Mounts a secondary cam or tool on the rear rod end to operate a separate mechanism or trigger DMSE electronic sensors.
Is the Airtac SAID100 Double Rod Cylinder SAID100X145S the Right Cylinder?
Choose this 100 mm bore when a 80 mm bore (2268 N at 0.5 MPa) lacks the power for symmetric push-pull cycles, or step down if 3681 N is excessive. A double-rod design is selected over a single-rod SAI when the mechanism requires dual-side guidance to prevent rotation, or needs to drive a second tool from the rear rod.
This cylinder does not hold its load when air is removed; it will drift without live pressure. For position holding, use an external pilot-operated check valve or explore SAIL and BSAID variants. It is dimensionally interchangeable per ISO 15552, using a PT G1/2 port and the reduced SAID mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2). At 145 mm stroke, side-load is minimal, but long unsupported strokes still require an external guide.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SAID100 Double Rod Cylinder SAID100X145S FAQ
It delivers equal force in both directions because the rod area is subtracted from both sides. It provides 3681 N at 0.5 MPa, 5153 N at 0.7 MPa, and 6626 N at 0.9 MPa.
Yes, the SAID100X145-S is dimensionally interchangeable with other ISO 15552 profile cylinders. It uses a G1/2 PT port and supports the Basic, FA, LB, TC, FTC, TCM1, and TCM2 mounting interfaces.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SAI Cylinders
Request a Quote for Airtac SAID100 Double Rod Cylinder SAID100X145S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.