Airtac SAID100 Double Rod Cylinder SAID100X190S
The AirTAC Airtac SAID100 Double Rod Cylinder SAID100X190S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø100mm bore and 190mm stroke, G1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ100 mm
- Stroke190 mm
- Port sizeG1/2
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SAID100 Double Rod Cylinder SAID100X190S
The AirTAC SAID100X190-S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 100mm bore and 190mm stroke. Because a rod exits both end covers, the annulus area is identical on each side, yielding equal push and pull forces of 3681 N at 0.5 MPa. This through-rod architecture allows you to mount the primary workpiece on the front end and a position flag or cam on the rear.
Equipped with a magnetic piston (-S), it supports AirTAC CMSE reed and DMSE electronic solid-state sensors along the dual extruded barrel grooves. The carbon steel rod thread is M20x1.5, and fluid control is managed via G1/2 ports. Adjustable air cushions at both ends decelerate the piston smoothly near stroke end.
Airtac SAID100 Double Rod Cylinder SAID100X190S Technical Specifications
| Model | Airtac SAID100 Double Rod Cylinder SAID100X190S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 190 mm |
| Acting type | Double acting |
| Port size | G1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SAID100 Double Rod Cylinder SAID100X190S
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×190 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SAID100 Double Rod Cylinder SAID100X190S Is Used
Twin-Station Actuation
Drive two separate mechanisms simultaneously from a single piston, using the front rod for the primary work task and the rear rod for a secondary synchronized operation.
Anti-Rotation Slides
The dual rods provide inherent resistance to torsional rotation, keeping guided loads perfectly stable during horizontal transfer without external linear bearings.
Through-Rod Sensing
Mount a physical cam or limit flag on the rear rod end to trigger external mechanical switches, while using the integrated -S magnet with DMSE sensors for primary positioning.
Is the Airtac SAID100 Double Rod Cylinder SAID100X190S the Right Cylinder?
Select this 100mm bore when an application requires symmetric thrust of 3681 N in both directions, stepping up from a 80mm bore (2268 N) or down from a 125mm bore (5734 N). A double-rod design is preferred over a single-rod SAI when you need dual-side guidance to prevent rotation, or when a rear rod is required to drive a secondary mechanism. Note that the overall length is greater than a single-rod cylinder, requiring extra rear clearance.
For dimensionally interchangeable ISO 15552 drop-in replacements, match the 100mm bore, 190mm stroke, PT port thread, and mounting accessories (Basic, FA, LB, TC, FTC, TCM1, TCM2). This standard configuration includes the -S magnet for position sensing. Remember that adjustable cushions only decelerate the piston; they do not hold a load. If position holding without air pressure is required, consider a BSAID clamp-lock cylinder or an external pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SAID100 Double Rod Cylinder SAID100X190S FAQ
Because it is a double-rod cylinder, the effective piston area is identical on both sides. It provides an equal force of 3681 N at 0.5 MPa, 5153 N at 0.7 MPa, and 6626 N at 0.9 MPa in both the extend and retract directions.
Yes, the SAID100X190-S is dimensionally interchangeable per ISO 15552. You can use it as a drop-in replacement for other ISO 15552 profile double-rod cylinders by matching the 100mm bore, 190mm stroke, and mounting dimensions, using the available Basic, FA, LB, or TC brackets.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SAI Cylinders
Request a Quote for Airtac SAID100 Double Rod Cylinder SAID100X190S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.