
The AirTAC SAID200 Double Rod Cylinder SAID200AX290 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø200mm bore and 290mm stroke, G3/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID200X290 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 200 mm bore and 290 mm stroke. Because the twin rods occupy both piston sides, the annulus area is identical in each direction, yielding an equal extend and retract force of 15079 N at 0.5 MPa. A rod exits both end covers, allowing you to mount the primary workpiece on one end and a secondary cam, position flag, or guide on the opposite end for superior anti-rotation stability.
This unit is configured with a SUS420J2 stainless steel rod (material code A) for enhanced corrosion resistance and PT tapered port threads. The extruded aluminum barrel includes sensor grooves on both sides for flexible switch placement. Note that a plain SAID does not hold its load if air pressure is lost; use a BSAID clamp-lock or external rod lock for fail-safe positioning.
| Model | Airtac SAID200 Double Rod Cylinder SAID200AX290 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø200 mm |
| Stroke | 290 mm |
| Acting type | Double acting |
| Port size | G3/4 |
| Rod thread | M36×2 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 50 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 15080 N | 15080 N |
| 0.7 MPa | 21111 N | — |
| Max (@1.0 MPa) | 3075 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 200 | Bore size in mm. |
| ×290 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives large symmetric transfer lines where equal push and pull forces of 15079 N at 0.5 MPa are required to move heavy jigs smoothly in both directions.
Utilizes the twin-rod architecture to prevent mechanical twisting on heavy lifting slides, keeping the load perfectly guided without rotational drift.
Mounts a primary workpiece on the front rod and a secondary cam or position flag on the rear rod to sequence two mechanisms from one cylinder body.
Choose this 200 mm bore when an application demands massive symmetric force, as it provides 15079 N each way at 0.5 MPa. If your load is lighter, stepping down to the 160 mm bore yields 9425 N both ways, whereas the 200 mm is required for heavy-duty twin-station actuation. Since the stroke is 290 mm, the long unsupported rod span increases the risk of rod-bearing bending under side loads; always use an external guide to support the payload.
A double-rod design is preferred over a single-rod SAI when you need equal push and pull speeds or dual-side guidance. This model is dimensionally interchangeable per ISO 15552, acting as a direct replacement for other ISO 15552 double-rod cylinders. It uses the reduced SAID mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2), omitting FB, CA, CB, and CR accessories. It is built without a magnet (-S), so position sensing requires external flags rather than integrated CMSE or DMSE switches.
Quick checklist
The SAID200X290 provides an equal force in both extend and retract directions due to its double-rod design. It outputs 15079 N at 0.5 MPa, 21110 N at 0.7 MPa, and 27141 N at 0.9 MPa.
Yes, the SAID200X290 is a profile cylinder with an ISO 15552 mounting interface, making it dimensionally interchangeable with other ISO 15552 double-rod cylinders. It uses PT tapered ports and a SUS420J2 stainless steel rod.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.