
The AirTAC SAID32 Double Rod Cylinder SAID32BX10 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 10mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID32X10 is a double-acting, double-rod ISO 15552 profile cylinder featuring a compact 10 mm stroke. Because a SUS304 stainless steel rod exits both end covers, the effective piston area is identical on extend and retract, yielding exactly 345 N of force each way at 0.5 MPa. The twin-rod layout inherently resists rotation and allows you to mount a primary workpiece on the front rod while attaching a cam or position flag to the rear.
This configuration omits the rear magnet, so it does not support CMSE or DMSE solid-state sensors directly. It uses PT tapered port threading (G1/8) and relies on adjustable air cushions at both ends to decelerate the piston smoothly. Note that air cushions only slow the load near stroke end; they do not hold position if air pressure drops.
| Model | Airtac SAID32 Double Rod Cylinder SAID32BX10 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 10 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a short clamping jaw from the front rod while the rear rod simultaneously pushes an opposing element, ensuring equal 345 N force in both travel directions.
The dual SUS304 rods prevent mechanical twisting during the 10 mm stroke, keeping precision pick-and-place heads perfectly aligned without external guides.
Uses the through-rod design to actuate a primary valve on the front face and a secondary mechanical limit flag on the rear within a compact 32 mm bore envelope.
Choose this 32 mm bore when an application demands symmetric force and anti-rotation guidance in a very tight stroke envelope. If you need slightly higher output, stepping up to the 40 mm bore raises the both-direction force to 528 N at 0.5 MPa. Conversely, if you require position feedback on this compact unit, you would specify the -S magnet option to enable DMSE electronic or CMSE reed switches in the dual-side sensor grooves.
As a true ISO 15552 profile cylinder, it drops in seamlessly with other ISO 15552 double-rod footprints. It supports Basic, FA, LB, TC, FTC, TCM1, and TCM2 mounts (omitting FB, CA, CB, and CR). Because the stroke is only 10 mm, side-load stress on the rod bearing is minimal, but always ensure the rear rod has adequate clearance to protrude.
Quick checklist
Because the double-rod design has the same annulus area on both sides, it provides equal force in both directions: 345 N at 0.5 MPa, 483 N at 0.7 MPa, and 621 N at 0.9 MPa.
No. The adjustable air cushions only decelerate the piston near the stroke ends; they do not lock or hold the load. For position holding without live pressure, you would need an external rod lock, a pilot-operated check valve, or a related type like the BSAID clamp-lock cylinder.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.