
The AirTAC SAID32 Double Rod Cylinder SAID32BX105S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 105mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID32X105-S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 32mm bore and 105mm stroke. Because the SUS304 stainless steel rod exits both end covers, the annulus area is identical on each side. This means extend and retract forces are perfectly equal, delivering 483 N of thrust in both directions at 0.5 MPa.
Equipped with a piston magnet (-S), this variant directly supports AirTAC CMSE reed and DMSE electronic solid-state sensors mounted into the dual-side extruded barrel grooves. The rear rod extension is ideal for mounting a position flag or driving a secondary mechanism, while the PT tapered port threads ensure a robust pneumatic seal.
| Model | Airtac SAID32 Double Rod Cylinder SAID32BX105S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 105 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×105 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Push and pull a workpiece carriage with identical 483 N force, ensuring consistent acceleration and deceleration cycles without tuning pressure differentials.
Mount a CMSE or DMSE sensor target flag on the rear rod extension to trigger downstream logic without interfering with the primary front-side tooling.
Leverage the twin-rod geometry to guide a vertical lifting slide, preventing piston rotation and maintaining precise tool alignment over the 105mm travel.
Select this 32mm bore when an application requires 483 N of symmetric force both ways, or step down if less thrust is needed. Unlike a single-rod SAI cylinder, the SAID32X105-S twin-rod design provides superior anti-rotation resistance and allows dual-side guidance. It is dimensionally interchangeable per ISO 15552, utilizing a reduced mounting set of Basic, FA, LB, TC, FTC, TCM1, and TCM2 (omitting FB, CA, CB, and CR).
Note that the adjustable air cushions at both ends only decelerate the piston near stroke end; they do not hold a load. If position holding without live air pressure is required, consider an external rod lock or a related SAIL lock cylinder. For this 105mm stroke, side-load is minimal, but always ensure the workpiece is guided externally for optimal bearing life.
Quick checklist
Because it is a double-rod cylinder, the effective piston area is identical on both sides. It delivers an equal force of 345 N at 0.5 MPa, 483 N at 0.7 MPa, and 621 N at 0.9 MPa in both the extend and retract directions.
Yes, the SAID32X105-S is dimensionally interchangeable with other ISO 15552 profile cylinders. It shares the same mounting footprint and utilizes standard AirTAC mounting accessories like FA, LB, and TC brackets.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.