
The AirTAC SAID32 Double Rod Cylinder SAID32BX10S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 10mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID32X10-S is a double-acting, double-rod ISO 15552 profile cylinder featuring a compact 10mm stroke. Because the piston rod exits both end covers, the effective annulus area is identical on extend and retract, yielding equal force and speed in both directions. This 32mm bore generates 345 N each way at 0.5 MPa, ensuring perfectly symmetric motion control.
Equipped with a -S magnet, this model supports AirTAC CMSE reed and DMSE electronic sensors mounted into the dual side grooves of the extruded aluminum barrel. It features SUS304 stainless steel rods for superior corrosion resistance and utilizes PT tapered G1/8 ports. The rear rod extension is ideal for mounting a secondary cam or position flag while keeping the load guided against rotation.
| Model | Airtac SAID32 Double Rod Cylinder SAID32BX10S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 10 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a workpiece from one end while the opposing rod manages an identical counter-force, leveraging the 345 N equal bidirectional output at 0.5 MPa.
Uses the rear rod protrusion to trigger an external physical limit switch, while the internal magnet operates CMSE or DMSE sensors for dual-redundant position verification.
The twin SUS304 rods keep the payload guided and prevent torsional twisting during short 10mm clamping or indexing movements.
Select this double-rod cylinder when an application demands equal push and pull forces alongside anti-rotation guidance, rather than the single-sided output of a standard SAI unit. If your project requires slightly less force, stepping down is not an option below 32mm in this series, but stepping up to the 40mm bore yields 528 N at 0.5 MPa. For this 10mm stroke, side-loading is minimal, but external guides remain recommended for heavy off-center loads.
This model uses the reduced SAID mounting accessory set: Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting the FB, CA, CB, and CR brackets found on single-rod variants. Note that the adjustable air cushions at both ends only decelerate the piston near stroke end; this cylinder will drift and cannot hold a load if air pressure is lost. For locking requirements, consider the SAIL or BSAID series. It is dimensionally interchangeable per ISO 15552.
Quick checklist
Because it is a double-rod cylinder, the push and pull forces are equal. It generates 345 N in both directions at 0.5 MPa, 483 N at 0.7 MPa, and 621 N at 0.9 MPa.
Yes, it shares the exact ISO 15552 mounting interface dimensions, making it a direct replacement for other ISO 15552 profile cylinders, though it uses a reduced mounting bracket set (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.