
The AirTAC SAID32 Double Rod Cylinder SAID32BX125 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 125mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID32X125 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 32mm bore and 125mm stroke. Because the SUS304 stainless steel rod exits both end covers, the annulus area is identical on extend and retract, yielding perfectly symmetric force and speed. This design outputs 483N each way at 0.7 MPa, ensuring highly stable motion control.
Beyond equal bidirectional thrust, the twin-rod architecture allows you to mount a workpiece on the front rod end while attaching a cam, position flag, or secondary mechanism to the rear. The extruded aluminum barrel includes sensor grooves on both sides, though adding a magnet requires specifying the -S option to utilize CMSE or DMSE switches.
| Model | Airtac SAID32 Double Rod Cylinder SAID32BX125 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 125 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×125 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a transfer shuttle where the matching extend and retract speeds keep the cycle time consistent and prevent jerky transitions.
Guides a precision vertical slide, using the twin rods to resist torsional twisting without needing an external linear guide.
Mounts the primary tool on the front rod while utilizing the rear rod protrusion to trigger a mechanical limit valve.
Choose this 32mm bore when an application demands 483N of thrust in both directions alongside anti-rotation guidance. If your mechanism requires less force, stepping down is not an option in this series, but if you need significantly higher bidirectional output, a 40mm bore provides 739N at the same 0.7 MPa. The PT tapered port threads ensure a robust pneumatic seal.
This model uses the reduced SAID mounting accessory set (Basic, FA, LB, TC, FTC, TCM1, TCM2), omitting the FB, CA, CB, and CR brackets found on single-rod variants. Note that the adjustable air cushions only decelerate the piston near stroke end; they do not hold a load. If position holding without live air pressure is required, consider an external rod lock or the BSAID clamp-lock series. Since the stroke is 125mm, side-load stress on the rod bearing is moderate, but external guidance is recommended for heavy radial loads.
Quick checklist
Because it is a double-rod cylinder, the force is identical in both directions. It provides 345N at 0.5 MPa, 483N at 0.7 MPa, and 621N at 0.9 MPa for both extension and retraction.
Yes, it is dimensionally interchangeable per ISO 15552. However, the SAID series uses a specific mounting subset: Basic, FA, LB, TC, FTC, TCM1, and TCM2. It does not support the FB, CA, CB, or CR brackets found on single-rod SAI models.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.