
The AirTAC SAID32 Double Rod Cylinder SAID32BX210S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 210mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID32X210-S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 32mm bore and 210mm stroke. Because the piston rod exits both end covers, the effective annulus area is identical in both directions, yielding an equal push and pull force of 483N at 0.7 MPa. This through-rod geometry provides superior anti-rotation guidance compared to a single-rod SAI unit.
Equipped with a magnet (-S), this variant supports AirTAC CMSE reed and DMSE electronic sensors along the dual-side barrel grooves. The rods are constructed from SUS304 stainless steel (code B) for corrosion resistance, and fluid connections use PT tapered threads. The rear rod extension can drive a secondary mechanism or mount a position flag, though you must account for the extra rear clearance.
| Model | Airtac SAID32 Double Rod Cylinder SAID32BX210S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 210 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×210 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a workpiece from one end while the opposing rod manages an identical counter-load, utilizing the equal 483N bidirectional thrust for balanced material handling.
Leverages the twin-rod architecture to prevent mechanical twisting during vertical lifting, maintaining precise linear guidance without external rails.
Mounts a primary tool on the front rod end and a secondary cam or position flag on the rear protrusion to trigger DMSE electronic sensors sequentially.
Select this 32mm bore when an application demands symmetric force and speed on both strokes, providing 345N each way at 0.5 MPa. If you need higher thrust, stepping up to the 40mm bore increases the both-way output to 528N at 0.5 MPa. The double-rod design is chosen over a single-rod cylinder when twin-station actuation or rigid anti-rotation guidance is required.
As a dimensionally interchangeable ISO 15552 component, it replaces other standard double-rod profile cylinders using Basic, FA, LB, TC, FTC, TCM1, or TCM2 mounts (omitting FB/CA/CB/CR). At a 210mm stroke, the 12mm rod and M10x1.25 thread handle moderate side loads, but an external guide is recommended for heavy off-center payloads. Note that the adjustable air cushions only decelerate the piston near stroke end; this cylinder will drift if air pressure is lost, so specify a SAIL or BSAID lock variant if position holding is needed.
Quick checklist
Because it is a double-rod cylinder, the effective piston area is the same on both sides. It provides an equal push and pull force of 345N at 0.5 MPa, 483N at 0.7 MPa, and 621N at 0.9 MPa.
Yes, it shares the exact ISO 15552 mounting interface dimensions and profile barrel design, allowing it to serve as a direct replacement for comparable double-rod cylinders using standard FA, LB, or TC mounts.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.