
The AirTAC SAID32 Double Rod Cylinder SAID32BX250 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 250mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID32X250 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 32mm bore and 250mm stroke. Because the SUS304 stainless steel rod exits both end covers, the annulus area is identical on both sides, yielding exactly 483N of force in both extend and retract directions at 0.7 MPa. This symmetric output is ideal for mechanisms requiring consistent power delivery without the speed differential found in single-rod units.
The twin-rod architecture allows you to mount the primary workpiece on the front rod end while using the rear protrusion for a cam or position flag. It features adjustable air cushions at both ends (27mm stroke) to decelerate the piston smoothly. Note that the overall length is greater than a standard SAI cylinder, requiring additional rear clearance for the secondary rod.
| Model | Airtac SAID32 Double Rod Cylinder SAID32BX250 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 250 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×250 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a transfer arm where the 483N extend and retract forces must match perfectly to avoid jerky movements during bidirectional part shuttling.
Uses the protruding rear rod end to trigger a mechanical limit valve while the front rod performs the primary clamping operation.
Powers a vertical lifting slide where the twin rods prevent the platform from twisting under offset loads.
Choose this 32mm bore when an application demands exactly 345N of bidirectional force at 0.5 MPa alongside anti-rotation guidance. If your mechanism requires less force, stepping down is not an option in this series, but stepping up to a 40mm bore provides 528N both ways. Select the SAID double-rod over a single-rod SAI when you need to drive a second mechanism from the rear or require superior resistance to torsional loads. Since this is a 250mm stroke, the unsupported 12mm rod can experience bending under lateral loads; always use an external linear guide for side-load support.
This cylinder uses PT tapered ports sized G1/8 and accepts the reduced SAID mounting accessory set: Basic, FA, LB, TC, FTC, TCM1, and TCM2 (omitting FB, CA, CB, and CR). It is dimensionally interchangeable per ISO 15552. Remember that a plain SAID does not hold position when air pressure is lost; for locking needs, consider the SAIL or BSAID variants.
Quick checklist
Because it is a double-rod cylinder, the force is identical in both directions. It delivers 345N at 0.5 MPa, 483N at 0.7 MPa, and 621N at 0.9 MPa for both extend and retract strokes.
Yes, it is dimensionally interchangeable with ISO 15552 profile cylinders, but the SAID series uses a reduced mounting set: Basic, FA, LB, TC, FTC, TCM1, and TCM2. It does not support FB, CA, CB, or CR mounts.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.