
The AirTAC SAID32 Double Rod Cylinder SAID32BX260S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 260mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID32X260-S is a double-acting, double-rod ISO 15552 profile cylinder. Because the SUS304 stainless steel rod exits both end covers, the annulus area is identical on extend and retract, yielding exactly 483 N of force in both directions at 0.7 MPa. The integrated magnet (-S) directly supports rear-mounted CMSE or DMSE position sensing.
This configuration uses PT tapered port threads and features an extruded aluminum barrel with sensor grooves on both sides. The twin-rod architecture provides superior anti-rotation guidance compared to a single-rod SAI, allowing you to drive a primary workpiece on one end and mount a cam or limit flag on the rear rod.
| Model | Airtac SAID32 Double Rod Cylinder SAID32BX260S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 260 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×260 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a transfer shuttle where the 483 N push and pull forces must be perfectly matched to maintain consistent timing on both strokes without recalibrating pressure.
The twin 12 mm SUS304 rods guide the load against rotation, ideal for vertical lifting slides that cannot twist during the 260 mm travel.
Mounts the primary tool on the front rod while using the rear rod extension to trigger a DMSE solid-state sensor flag, saving space on the front end.
Select this 32 mm bore when an application demands symmetric 483 N force both ways and dual-side guidance. If you need less thrust, dropping to a smaller bore is not an option within the SAID range, but stepping up to a 40 mm bore increases the bidirectional force to 739 N at 0.7 MPa. At a 260 mm stroke, the 12 mm rod experiences leverage stresses under side-loading, so an external guide rail is recommended to prevent premature rod-bearing wear.
Because this is a standard double-acting cylinder, the adjustable air cushions only decelerate the piston near the stroke ends and do not hold the load if air pressure is lost. For direct compatibility, it matches ISO 15552 mounting dimensions and uses the SAID accessory set (Basic, FA, LB, TC, FTC, TCM1, TCM2), omitting the FB, CA, CB, and CR brackets found on single-rod variants.
Quick checklist
It delivers 345 N at 0.5 MPa, 483 N at 0.7 MPa, and 621 N at 0.9 MPa. Because it is a double-rod cylinder, the force is identical in both the extend and retract directions.
Yes, it is dimensionally interchangeable per ISO 15552. It uses the same mounting footprint but utilizes the reduced SAID bracket set (Basic, FA, LB, TC, FTC, TCM1, TCM2) and excludes single-rod only mounts like FB and CA.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.