
The AirTAC SAID32 Double Rod Cylinder SAID32BX325 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 325mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID32X325 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 32mm bore and 325mm stroke. Because the SUS304 stainless steel rod exits both end covers, the effective piston area is identical on extend and retract. This yields exactly 345N of force in both directions at 0.5MPa, ensuring perfectly symmetric motion.
This configuration uses PT tapered port threads and lacks a piston magnet. The twin-rod architecture provides superior anti-rotation stability compared to a single-rod SAI. You can mount the primary workpiece on the front rod end and use the rear extension to drive a secondary mechanism or trigger a limit flag.
| Model | Airtac SAID32 Double Rod Cylinder SAID32BX325 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 325 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×325 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a shuttle mechanism where the 345N force must remain perfectly identical in both directions without speed fluctuations.
The twin 12mm SUS304 rods guide the payload securely, preventing torsional deflection during horizontal clamping.
Mounts the primary tool on the front rod while the rear extension drives a mechanical cam or triggers a limit switch.
Choose this 32mm bore when an application demands equal push and pull forces, specifically 345N at 0.5MPa. If your process requires less force, stepping down is not an option in this series, but stepping up to a 40mm bore yields 528N both ways. Select the double-rod SAID over a single-rod SAI when you need dual-side guidance to prevent torsional twist or require rear-rod sensing capabilities.
At 325mm of stroke, the 12mm rod is highly susceptible to side-loading and bending under offset loads; always use an external linear guide to support the workpiece. This cylinder uses a reduced mounting accessory set (Basic, FA, LB, TC, FTC, TCM1, TCM2) and omits FB, CA, CB, and CR brackets. Note that the adjustable air cushions only decelerate the piston near stroke end; they do not hold the load if air pressure is lost. For position holding, use an external pilot-operated check valve.
Quick checklist
Because the rod occupies both sides of the piston, the extend and retract forces are equal. It outputs 345N both ways at 0.5MPa, 483N at 0.7MPa, and 621N at 0.9MPa.
Yes, it is dimensionally interchangeable per ISO 15552. It serves as a direct replacement for other ISO 15552 double-rod profile cylinders, using the standard PT G1/8 port and standard mounting dimensions.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.