
The AirTAC SAID32 Double Rod Cylinder SAID32BX45 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 45mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID32X45 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 32mm bore and 45mm stroke. Because the SUS304 stainless steel rod exits both end covers, the effective piston area is identical in each direction. This provides an equal extend and retract force of 483 N at 0.5 MPa, ensuring perfectly symmetric motion for demanding positioning tasks.
Beyond balanced thrust, the twin-rod architecture allows you to mount the primary workpiece on the front rod end while using the rear protrusion for a cam or position flag. The extruded aluminum barrel includes sensor grooves on both sides, though position monitoring requires adding a magnet. It uses PT tapered port threads and adjustable air cushions at both ends to decelerate the piston smoothly.
| Model | Airtac SAID32 Double Rod Cylinder SAID32BX45 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 45 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×45 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a transfer shuttle where the 483 N push and pull forces must be perfectly matched to maintain consistent cycle timing without tweaking regulator pressures.
Powers a vertical lifting slide using the twin SUS304 rods to resist torsional deflection, keeping the payload guided securely without external linear bearings.
Actuates a small clamping jaw on the front rod while the rear rod end protrudes to physically trigger a mechanical limit switch at mid-stroke.
Select this 32mm bore when an application demands equal 483 N thrust in both directions, which is a step down in force from the 50mm bore (825 N at 0.5 MPa) but offers a more compact footprint. A double-rod design is preferred over a single-rod SAI when you need dual-side guidance to prevent rotation or require a rear rod end to trigger a secondary mechanism. This cylinder uses the reduced SAID mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2) and omits FB, CA, CB, and CR brackets.
For a direct replacement, match the 32mm bore, 45mm stroke, PT port thread, and your required mounting accessory. Note that the adjustable air cushion only decelerates the piston near stroke end; it does not hold the load. If the system loses air pressure, the cylinder will drift, requiring an external pilot-operated check valve or a SAIL lock cylinder for position holding.
Quick checklist
Because the rod occupies both sides of the piston, the effective annulus area is equal in both directions. The SAID32X45 delivers 345 N at 0.5 MPa, 483 N at 0.7 MPa, and 621 N at 0.9 MPa on both the extend and retract strokes.
Yes, the SAID32X45 is dimensionally interchangeable per ISO 15552 mounting interface dimensions. You can use it as a direct replacement for other ISO 15552 profile double-rod cylinders, provided you use the PT port thread and compatible mounting brackets.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.