
The AirTAC SAID32 Double Rod Cylinder SAID32BX50S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 50mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID32X50-S is a double-acting, double-rod ISO 15552 profile cylinder. A single piston drives a SUS304 stainless steel rod out of both end covers, yielding exactly 483N of force in both extend and retract directions at 0.5 MPa. Because the annulus area is identical on both sides, push and pull forces remain perfectly balanced.
This through-rod design allows you to mount the primary workpiece on the front end and a position flag or cam on the rear. The extruded aluminum barrel features sensor grooves on both sides, and the included magnet (-S) pairs directly with AirTAC CMSE reed or DMSE electronic solid-state switches for precise end-of-stroke detection.
| Model | Airtac SAID32 Double Rod Cylinder SAID32BX50S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 50 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a dual-station actuation system where the 483N equal push and pull force ensures perfectly balanced movement without speed fluctuations.
Powers a guided linear slide using the twin SUS304 rods to prevent mechanical twisting under offset loads, maintaining strict alignment.
Actuates a primary clamping tool on the front stroke while the rear rod end trips a DMSE solid-state sensor for position verification.
Select this 32mm bore when an application demands equal 483N force both ways and superior anti-rotation guidance compared to a single-rod SAI. If your mechanism requires less force, stepping down is not an option in this series, but stepping up to a 40mm bore provides 739N. Remember that the adjustable air cushions only decelerate the piston near stroke end; a plain SAID will drift if air pressure is lost. For load-holding without live pressure, consider an external pilot-operated check valve or the BSAID clamp-lock variant.
This model is dimensionally interchangeable per ISO 15552, making it a direct replacement for other ISO 15552 double-rod cylinders. It uses PT tapered ports (G1/8) and supports a reduced mounting set of Basic, FA, LB, TC, FTC, TCM1, and TCM2. The 50mm stroke keeps the unsupported rod length short, minimizing rod-bearing bending and side-load stress.
Quick checklist
Because the rod occupies both sides of the piston, the effective area is identical in both directions. It provides 345N at 0.5 MPa, 483N at 0.7 MPa, and 621N at 0.9 MPa for both extend and retract strokes.
Yes, it is dimensionally interchangeable with ISO 15552 profile cylinders. It supports a specific subset of mounts: Basic, FA, LB, TC, FTC, TCM1, and TCM2. It does not use the FB, CA, CB, or CR mounts found on single-rod variants.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.