
The AirTAC SAID32 Double Rod Cylinder SAID32BX95S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 95mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID32X95-S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 32mm bore and 95mm stroke. Because the SUS304 stainless steel rod exits both end covers, the effective piston area is identical on extend and retract, yielding exactly 483 N of force in each direction at 0.5 MPa. This symmetric output is ideal for mechanisms requiring consistent push and pull dynamics.
Equipped with a factory-installed magnet (-S), the barrel integrates sensor grooves on both sides to accept CMSE reed or DMSE electronic solid-state switches. The PT tapered porting (G1/8) and adjustable air cushions at both ends ensure reliable operation across the 30-800 mm/s speed range, while the rear rod end provides a convenient mounting point for a position flag or secondary cam.
| Model | Airtac SAID32 Double Rod Cylinder SAID32BX95S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 95 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×95 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a transfer shuttle where the push and pull strokes must move identical payloads at the exact same speed, leveraging the equal 483 N annulus force.
Powers a vertical lifting slide where the twin SUS304 rods prevent the platform from twisting under offset loads, ensuring smooth linear guidance.
Actuates a primary workpiece on the front rod end while driving a rear-mounted cam to trigger a DMSE electronic sensor for a secondary sequence.
Select this 32mm bore when an application demands equal 345 N force both ways at 0.5 MPa, stepping down from a 40mm bore (528 N) if excessive thrust risks damaging the workpiece, or stepping up from smaller compact cylinders that lack the rigidity for dual-side loads. The double-rod design is specifically chosen over a single-rod SAI when the load requires anti-rotation guidance or when a rear-mounted sensor flag is needed to track the exact position of the rear rod end.
As a dimensionally interchangeable ISO 15552 cylinder, it serves as a direct replacement for other standard profile cylinders, utilizing the reduced SAID mounting accessory set (Basic, FA, LB, TC, FTC, TCM1, TCM2) without the FB, CA, CB, or CR variants. Note that a plain SAID does not hold its position if air pressure is lost; for dead-load holding, consider a SAIL lock cylinder or an external pilot-operated check valve. The adjustable cushions only decelerate the piston near the stroke ends.
Quick checklist
Because the rod occupies both sides of the piston, the effective area is equal in both directions. It provides 345 N at 0.5 MPa, 483 N at 0.7 MPa, and 621 N at 0.9 MPa for both extension and retraction.
Yes, it is dimensionally interchangeable per ISO 15552 and serves as a direct replacement for standard profile cylinders. It uses the PT port standard and supports the SAID mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.