
The AirTAC SAID63 Double Rod Cylinder SAID63AX100 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø63mm bore and 100mm stroke, G3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID63X100 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 63mm bore and 100mm stroke. Because the twin rods occupy both piston faces, the annulus area is identical in both directions, yielding an equal extend and retract thrust of 1402N at 0.5MPa. A single piston drives a rod out of both end covers, allowing you to mount the primary workpiece on one end and a secondary cam, position flag, or sensor target on the opposite rear rod end.
This unit is configured with a SUS420J2 stainless steel rod (material code A) for enhanced corrosion resistance and uses PT tapered port threads. The extruded aluminum barrel includes sensor grooves on both sides for flexible switch mounting. Note that the overall length is longer than a single-rod SAI variant, as the rear rod protrudes through the back cover and requires corresponding clearance in your layout.
| Model | Airtac SAID63 Double Rod Cylinder SAID63AX100 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 100 mm |
| Acting type | Double acting |
| Port size | G3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | — |
| Max (@1.0 MPa) | 286 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 63 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a workpiece with identical 1402N thrust in both extend and retract directions, ensuring perfectly balanced motion for push-pull assemblies.
Uses the front rod to drive the primary load while the rear rod simultaneously operates a secondary mechanism or parallel station.
The dual-rod architecture prevents piston rotation, providing highly stable linear guidance for precision sliding and lifting fixtures.
Choose this 63mm bore when an application demands equal push and pull forces alongside dual-side guidance to prevent rotation. If your mechanism requires less thrust, stepping down to the 50mm bore provides 825N both ways at 0.5MPa. Conversely, heavier transfers may need the 80mm bore offering 2268N. The double-rod design is preferred over a single-rod SAI when you need to drive twin stations or synchronize a secondary mechanism from the rear rod.
This model uses PT tapered ports and omits the magnet (-S), so position sensing requires external flags or separate detection. It supports the reduced SAID mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2), omitting the FB, CA, CB, and CR accessories found on single-rod versions. Remember that the adjustable air cushions only decelerate the piston near stroke end; this cylinder will drift if air pressure is lost. For fail-safe load holding, consider the SAIL or BSAID variants. It is dimensionally interchangeable per ISO 15552.
AirtacDistr lists every SAID63 order code with its price on one page at https://airtacdistr.com/products/airtac-said63-double-rod-iso-cylinder
Quick checklist
Because the double-rod design creates equal annulus areas on both sides, it provides 1402N of force in both extend and retract directions at 0.5MPa, and 1962N at 0.7MPa.
Yes, it shares the standard ISO 15552 mounting interface and dimensions, making it a direct replacement for other ISO 15552 double-rod cylinders. It supports Basic, FA, LB, TC, FTC, TCM1, and TCM2 mounts.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.