
The AirTAC SAID63 Double Rod Cylinder SAID63AX155 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø63mm bore and 155mm stroke, G3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID63X155 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 63mm bore and 155mm stroke. Because a piston rod exits both end covers, the annulus area is identical on extension and retraction, yielding a perfectly symmetrical 1402N output force at 0.5 MPa in both directions. This through-rod design provides superior anti-rotation guidance for loads compared to a single-rod SAI.
This specific configuration features a SUS420J2 stainless steel rod for enhanced corrosion resistance and utilizes PT tapered port threading. The extruded aluminum barrel includes sensor grooves on both sides for flexible mounting of CMSE or DMSE switches. Note that the rear rod protrudes during operation, requiring appropriate clearance and offering a convenient mounting point for a cam or position flag.
| Model | Airtac SAID63 Double Rod Cylinder SAID63AX155 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 155 mm |
| Acting type | Double acting |
| Port size | G3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | — |
| Max (@1.0 MPa) | 286 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 63 | Bore size in mm. |
| ×155 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Ideal for mechanisms requiring identical push and pull kinetics, leveraging the 1402N both-way output to drive balanced clamping and release cycles without force bias.
The dual through-rod construction prevents piston twisting under offset loads, providing stable guidance for precision sliding and lifting fixtures.
The protruding rear rod drives secondary mechanisms or triggers mechanical limit flags, allowing complex dual-station automation from a single actuator.
Select this 63mm bore cylinder when an application demands equal push and pull forces, stepping up from the 50mm bore (825N at 0.5 MPa) or down from the 80mm bore (2268N at 0.5 MPa). The twin-rod architecture is chosen over a single-rod SAI when dual-side guidance, anti-rotation control, or a rear-rod cam/flag is required. Since the 155mm stroke is under 300mm, side-load bending stress on the rod bearing is moderate, though external guides are recommended for heavy off-center loads.
This model is dimensionally interchangeable per ISO 15552, making it a direct replacement for other ISO 15552 double-rod cylinders. It uses a PT port and supports a reduced mounting accessory set (Basic, FA, LB, TC, FTC, TCM1, TCM2), omitting the FB, CA, CB, and CR variants. As a standard double-acting cylinder, it does not hold position if air pressure is lost; for fail-safe holding, consider the SAIL or BSAID series. No magnet is specified for this unit.
AirtacDistr lists every SAID63 order code with its price on one page at https://airtacdistr.com/products/airtac-said63-double-rod-iso-cylinder
Quick checklist
Because it is a double-rod cylinder, the effective piston area is identical in both directions. It delivers 1402N of force at 0.5 MPa, 1962N at 0.7 MPa, and 2523N at 0.9 MPa for both extension and retraction.
Yes, the SAID63X155 is dimensionally interchangeable per ISO 15552 and serves as a direct replacement for other ISO 15552 double-rod cylinders. It uses a PT G3/8 port and supports Basic, FA, LB, TC, FTC, TCM1, and TCM2 mounts.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.